cvnf14p3ordy
Members-
Content Count
255 -
Joined
-
Last visited
About cvnf14p3ordy
-
Rank
Tenax Sniffer (Open a window!)
- Birthday 07/04/1970
Profile Information
-
Gender
Male
-
Location
SE Wisconsin
-
Interests
Military Aviation<br />
Recent Profile Visitors
6,032 profile views
-
I found a sheet made by CAM decals - finally. Thanks for the replies and suggestions.
-
Thanks loki I'll take a look at your link.
-
Scotthidr, yea I just need a pair of low-viz, tac gray USS George Washington decals in 1/48 scale. But, if I have to buy an entire sheet to get them so be it.
-
Gents, I'm in need of a set of low-viz USS George Washington decals in 48 scale for a custom F/A-18F that is just about finished. I did some research and keep seeing that Cam Decals has a sheet but I can't find them anywhere including Sprue Bros. I searched the forum here and found nothing, so I decided to post this; do you guys have any suggestions or ideas? Thanks in advance,
-
Roger that
-
Darren I have one I can part with, let me know. - Tom
-
Trumpeter and Tamiya both have 1/32nd scale kits; I'd recommend the Tamiya kit, I have a few friends who tried the Trumpy kit who had a lot of problems. Cost was another issue, the Trumpy kit is pretty expensive. As far as the B/D goes, there is quite a bit of aftermarket conversion sets to help convert an A to either a B or D, check Sprue Brothers out. Keep in mind though that VF-1 was strictly fighter, no air to ground or TARPS capabilities prior to their disestablishment in 1994. Hope that helps!
-
Can anyone direct me to where I might be able to find downloadable installation directions for the Black Box F/A-18F cockpit for the Revell/Monogram kit pleeease! Or if any of you have the directions could you possibly scan and email them to me? I'd really appreciate it - thanks in advance!
-
Seawinder, thanks for the reply man. Nope, the names are black. I attached two photos of my bud's name and his pilot. There would be 2 other names that would be on the port-side and my name on the nose gear door. Let me know what you think. Thanks!
-
Thanks for the reply IKAR...What was the turn around on your decals? I had never heard of them and this could be awesome, thanks for the gouge man!
-
I'm building a 1/48 F/A-18F for a WSO friend of mine who just transferred from VFA-102 to VX-9. I purchased the Hasegawa low-viz VFA-102 kit and a lot of other aftermarket stuff. Problem I'm running into is I can't find a pair of low-viz USS George Washington decals, the ones that go below the vertical stabs by the horizontal formation lights (see attached photo). Do any of you guys have a pair in your spares box? I'm more than willing to send a couple bucks or trade something. I also am looking for someone that is able to make decals of the crew names for this specific build. I have photos of
-
I scratch built them for my last Rhino and this has been the best photo I've been able to find thus far. I'm building a 1/48 scale for a WSO friend of mine and I want it to be as accurate as possible. Thanks for the gouge guys.
-
Are there any aftermarket ECS exhaust ducts for the Super Hornet out there, either resin or photo-etch? Thanks in advance for the help.
-
Aftermarket Parts for R-M F-14D Super Tomcat
cvnf14p3ordy replied to ex-USMC_Hornet_WSO's topic in Jet Modeling
Glad to see you're building a real airplane... ; ) Have you visited Sprue Brothers yet? If you haven't Google it or I'm sure someone will post the link, (I'm on my cell). They have a great list of aftermarket stuff that may help. I know there's Aftermarket NACA vents out there for the M-61A1 and GEF110's but like you mentioned they aren't for that specific kit. Hope that helps, good luck sir.