Search the Community
Showing results for tags '1/350 scale'.
-
Rhapsody in Orange... OR...... "Gentlemen, I give you Orange October"....... Mikro-Mir USS Albacore - modified to an earlier configuration with + shaped rear dive planes and 'standard' propeller... She is painted in an orange primer coat before the application of topside black - as seen here......... Ken
-
- uss albacore
- 1/350 scale
-
(and 1 more)
Tagged with:
-
Braving the lockdown, my postman Martin has just delivered this new kit from Mikro-Mir Having already built a model of the USS Parche.......... I was going to pass on this new kit - until I realised it represents the pre-stretch early version........ As the boxart shows - the sail is different, she carries a DSRV (as a cover for her covert ops) - and the hull is 100ft shorter..... The shorter hull is is two halves - split horizontally... The only other sprue carries the sail, diving
- 7 replies
-
- uss parche
- submarine
-
(and 2 more)
Tagged with:
-
The latest 1/350 scale submarine kit from Zvezda is the massive Delta IV (Delfin) class of Russian SSBN.... Moulded in black plastic, the lower hull is made up from three sections - two lower vertically split sides plus a top.... The twin five-bladed propellers each have to made up from a central shaft - to which are attached the five separate scimitar-shaped blades The missile casing is also separate - made up from two side panels (below) and a top section (above)... This complex hull construction would
- 15 replies
-
- tula
- 1/350 scale
-
(and 2 more)
Tagged with:
-
Just finished - the USS Growler from Micro-Mir...... I didn't get an exact straight line for the waterline... (the port side is better..) Colours are from rattle cans of Halfords Grey and Red Plastic Primers - with Humbrol Panzer Grey enamel for the non-slip decking. I've just realised - in my rush to get it photographed and on here - I've forgotten to weather it!!! (It's an age thing) Ken PS - WIP is here
- 2 replies
-
- micro-mir
- 1/350 scale
-
(and 1 more)
Tagged with:
-
Another new arrival on the slips - the 1/350 scale injection-moulded kit of USS Growler from Mikro-Mir...... Box art... History and paint guide...... Instructions for the hull....... Regulus I Missile and conning tower..... Final assembly.... Vertically split hull - with excellent engraved detail..... Conning tower, decking and one half of the missile..... Minor parts, missile half, decals and etched-brass....
- 5 replies
-
- 1/350 scale
- mikro-mir
-
(and 1 more)
Tagged with:
-
Just purchased from OKB Grigorov....... http://shop.okbgrigorov.com/ A resin kit of the Royal Navy submarine R10 - launched in October 1918 - just to late for the Great War. At just14cm (5.5in) long, the hull is a single superb resin casting - with a separate conning tower and etched brass parts for the diving planes, propeller etc.. The service from OKB was great - just a week from order to delivery - although the box with the hull/brass/instructions arrived first, followed a week later by the conning tower in a separate Jiffy bag!!!
-
- 1/350 scale
- resin submarine
-
(and 1 more)
Tagged with:
-
Recently finished - the 1/350 scale resin kit of an Oberon Class diesel submarine from ebay seller subsmodels..... I chose to finish it as HMS Opossum - wearing a roughly-applied camouflage scheme used when she was on special ops during the Gulf War. She also sported a sharkmouth - sourced as a decal from my spares box. It isn't 100% accurate but it looks OK... I think I may have overdone the 'weathing' a bit on the camo........ The camouflage makes a nice change from the all-black finish normally found on R
- 1 reply
-
- resin sub kit
- 1/350 scale
-
(and 1 more)
Tagged with:
-
This is the 1/350 scale kit of HMS Resolution by MikroMir - finished as HMS Repulse when she was engaged in trials with the DSRV 'Avalon' rescue vessel... The DSRV kit is from Riich Models - it represents 'Mystic' - so needs some alterations to represent 'Avalon'..... The kit parts...... Etched brass propeller, struts etc... Mikro Mir HMS Resolution painted with hi-viz guidance markings as HMS Repulse...... A simple 'conversion' - but it adds to
- 1 reply
-
- repulse ssbn
- 1/350 scale
-
(and 1 more)
Tagged with:
-
One of the things I picked up at SMW Telford was a new resin kit of the Royal Navy submarine HMS Tabard - (thanks Chris for the heads-up) This Group III T-Class sub is made by Starling Models and is an excellent kit of an iconic British WWII sub. The resin parts come in a stout cardboard box - filled with polystyrene 'worms' to protect the contents.... The 8-page instruction booklet is well printed with eay to follow steps.... Note the two types of gun emplacement. Colour painting guide
- 8 replies
-
- t-class sub
- hms tabard
-
(and 3 more)
Tagged with:
-
Ever since finding this photo of the Balao-class sub USS Sealion, I have wanted to try and model her...... All I needed was a 1/350 scale model of a Sikorsky HRS-3 helicopter to place on her widened deck aft of the fairwater..... Then I found that Shapeways Models made a 3D-printed S-55 helicopeter - so I was ready to start... I'm using the AFV-Club Gato-class sub as a starting point....... Sealion is a Balao-class sub (improved Gato), so I needed a late-style fairwater - also made by Shapeways.....
- 9 replies
-
- submarine uss sealion lpss-315
- 1/350 scale
-
(and 1 more)
Tagged with: