wardog Posted January 20, 2012 Author Share Posted January 20, 2012 (edited) Over the next few days I'll be posting pics of the wings. The wings will be folded and for this I'm using the Paragon wing fold set. Although the set is very nice, it takes a lot of work to make the inserts come out nice. There are plenty of variables that dictate how much work you'll have to put in to make them come out right. These variables include shrinkage of resin pieces, thickness along the wing where the cuts were made and a few others. For those that want an easier route to the folded wing look, Wolfpack now makes a kit for this bird that has wing-fold mechanism already built into the 4 wing sections. The pics below show how i decided to tackle the incorrect placement of the inboard wing fences on the Monogram kit. Before i explain why i went the route i did with this fence installation, I'll explain what happened on a different project. I installed the ventral strakes on a Hasegawa F-8 with super glue and after many many hours of filling and sanding the join area, it was finally perfect. This unfortunately didn't last long as i broke one of them off due to careless handling. Bottom line is, regardless of the fact i used super glue, the width of the strake where it meets the fuselage just isn't that wide, maybe .020 or so max and this just doesn't provide a strong enough contact area. To avoid this from happening again on my current project, i decided to measure where the fence is located and cut slits into the wing to accommodate the fence. I used Dymo tape to mark the cut line and simply used my saw blades to cut thru the plastic. Only thing i had to be careful about was making sure i cut 90 degrees to the surface so that the fences sit perfectly vertical relative to the wing. The Dymo tape in the pic looks bent because i had already removed it and then put it back on for the pic. Although not shown, the surrounding area was also covered during cutting to protect it from errant slips of the hand/saw. The fences were made large enough vertically to rest on the bottom wing and will be glued there as well. If i break these off by accident, i need to find a new hobby. The other pic shows both fences being made simultaneously to avoid any inconsistency between fences if made separately. Edited January 20, 2012 by wardog Quote Link to post Share on other sites
wardog Posted January 20, 2012 Author Share Posted January 20, 2012 Couple of pics showing detail of the main wheel wells. Again, most of this detail can't really be seen all that well when the model is complete but it's nice to have it there anyway. Quote Link to post Share on other sites
wardog Posted January 20, 2012 Author Share Posted January 20, 2012 Amazing detail work, I can't wait to see what you would be able to do with a 1/32 scale model Thanks. The way my eyesight is going, i just might be doing 32nd scale birds before too long. Quote Link to post Share on other sites
wardog Posted January 23, 2012 Author Share Posted January 23, 2012 Got in a few hours to work on the model this weekend so i finished up the inboard wing fences. The process i used was rather simple and it worked better than i expected which is rare for me as nothing ever seems to go easy for me. Once i placed the fences in the slots i cut out, i simply glued them in with extra thin cyano and once dried, sanded away any excess glue from the general area. Once smooth, i followed with a couple of applications of Mr.Surfacer to fill any remaining gaps in the super glue. A little bit more sanding once dry to smooth it all out and presto, finished. Quote Link to post Share on other sites
wardog Posted January 23, 2012 Author Share Posted January 23, 2012 As i mentioned in the beginning of this WIP, i typically don't build models by following the instruction sheet but rather with whatever section i just happen to be interested in. I have a good percentage of this jet built but really want to start the cockpit so i can finally glue the fuselage halves together. Main reason I've been delaying building the cockpit is I'm waiting to see if Aires puts out a cockpit for this bird. This of course hasn't happened yet and I'm thinking it probably won't. The best thing out there now, at least in my opinion, is the Blackbox/Avionics set. Although this set is nice, there are a lot of inaccuracies with it. I believe some of the details are done incorrectly and others simply do not exist on the real thing. Think I'll wait another month or so and if nothing pops up I'll just go with the Blackbox/Avionics set and make the best of it. If anyone out there knows something i don't, please feel free to share. Quote Link to post Share on other sites
VA-115EFR Posted January 23, 2012 Share Posted January 23, 2012 I just have to say, that whatever inaccuracies are in the cockpit, I KNOW you have the skill to correct them! Quote Link to post Share on other sites
chuck540z3 Posted January 23, 2012 Share Posted January 23, 2012 (edited) Seems like my airbrush doesn't like enamels as much as acrylics. Needless to say, it will get smoothed out and re-painted. Wow, you do excellent work, especially your scratch building of so much nice detail. Bravo! Since I use MM enamels all the time and have had the same problem with them "dusting", here's a few tips you might consider. These enamels go on best with thin coats sprayed fairly close to the model at fairly low pressure (~15 psi). If you goose up the pressure and try to spray more of an overall cover coat, tight spots where the air/paint mixture blow around come out dusty due to the paint droplets drying before settling on the model. For these tight areas I thin the paint even more and spray at even lower pressures. Dusting still happens, but I find it happens a lot less now and a quick touch-up with 2000# grit sandpaper gets rid of it fairly easily. Also, don't use any "heat" like lacquer thinner which promotes drying too quickly. I find the Testors paint thinner dries quick enough and it's of course it's compatible with the entire Model Master line of enamels. I really prefer enamel paints over acrylics for a number of reasons, but of course a respirator and a paint booth are a must. Edited January 23, 2012 by chuck540z3 Quote Link to post Share on other sites
wardog Posted January 23, 2012 Author Share Posted January 23, 2012 Chuck, thanks for the kind words. I'm by no means a real experienced modeler like a lot of the folks on this site and the 2 projects I've completed in the last few years have been learn as I go projects. This is why each project usually takes me a few years to complete as I have to re-do everything. What I can say is that since I like super detailing a lot, i've become fairly decent at it. Problem is my painting skills are not up to par as the painting process is rather quick in comparison to the hundreds of construction hours spent on a model. This of course means the painting learning curve is a lot lengthier. I've only recently encountered painting issues with MM paints. When I painted my F-4 I used a Paasche VL and had no problems. Paint layed down great. I'm now using two better brushes, a Tamiya HG and an Iwata revolution and these are the ones giving me problems. Seems like they just prefer really thin liquids to spray good. I also changed laquer thinner brand and it may be too hot. I'll try your advice. Thanks for the help. Quote Link to post Share on other sites
cruiz Posted January 24, 2012 Share Posted January 24, 2012 What a great job you are doing here! Of all the abilites you show, what I found more inspiring is the cleanliness of your work and how every piece is square and aligned. I’ll be following this build with interest; thank you for posting your work. Regards Carlos Quote Link to post Share on other sites
HOLMES Posted January 24, 2012 Share Posted January 24, 2012 wardog, HELLO and How the heck did I MISS this OUTSTANDING ,FLAWLESS and SO VERY NEAT work.. I think this is EXEMPLARY , IMPRESSIVE bit of modeling.. The details is just MIND BLOWING and BREATHTAKING...PHENOMENAL..EXQUISITE workmanship... I have a new FAVORITE Modeler folks...Ooops sorry, I mean MODELING GOD ! HOLMES Quote Link to post Share on other sites
Ian Cooper Posted January 24, 2012 Share Posted January 24, 2012 Yeah, this is OK, isn't it! Wow. Quote Link to post Share on other sites
edwards scissorhands Posted January 24, 2012 Share Posted January 24, 2012 faboulous!! you're doing a very nice job with that bird!!! Are you using a pin vise n80 for the rivets or just a pin?? thank you merci!! olivier Quote Link to post Share on other sites
wardog Posted January 25, 2012 Author Share Posted January 25, 2012 What a great job you are doing here! Of all the abilites you show, what I found more inspiring is the cleanliness of your work and how every piece is square and aligned. I’ll be following this build with interest; thank you for posting your work. Regards Carlos Gracias amigo. I do try to put a lot of emphasis on making sure things are square as i feel the effort is worth the results. Sometimes i go a little overboard with it but i just blame it on a medical condition. Thanks for looking. Saludos Quote Link to post Share on other sites
wardog Posted January 25, 2012 Author Share Posted January 25, 2012 wardog, HELLO and How the heck did I MISS this OUTSTANDING ,FLAWLESS and SO VERY NEAT work.. I think this is EXEMPLARY , IMPRESSIVE bit of modeling.. The details is just MIND BLOWING and BREATHTAKING...PHENOMENAL..EXQUISITE workmanship... I have a new FAVORITE Modeler folks...Ooops sorry, I mean MODELING GOD ! HOLMES Quote Link to post Share on other sites
wardog Posted January 25, 2012 Author Share Posted January 25, 2012 wardog, HELLO and How the heck did I MISS this OUTSTANDING ,FLAWLESS and SO VERY NEAT work.. I think this is EXEMPLARY , IMPRESSIVE bit of modeling.. The details is just MIND BLOWING and BREATHTAKING...PHENOMENAL..EXQUISITE workmanship... I have a new FAVORITE Modeler folks...Ooops sorry, I mean MODELING GOD ! HOLMES Thanks Holmes. No God here, just like to take my time with whatever project I'm working on. The longer you take the nicer they come out....usually. Thanks again. Quote Link to post Share on other sites
wardog Posted January 25, 2012 Author Share Posted January 25, 2012 (edited) faboulous!! you're doing a very nice job with that bird!!! Are you using a pin vise n80 for the rivets or just a pin?? thank you merci!! olivier Thanks. For the rivets/fasteners, i typically use a thin needle in a pin vice or drills between a #90-97. I never use a #80 bit as i feel it's way too big for 48th scale. Personally i think it might even be too big for 32nd scale. The decimal equivalent for the drills i use go down to about .006 in. or so. The attached link shows some size comparisons between a #90 top, #80 center and a #97 bottom. These smaller drills are not twist drills like the #80 as the cutting flutes are different. They tend to want to thread themselves into plastic as opposed to removing the plastic like a twist drills does. This can sometimes be a problem as you have to twist them out as opposed to pulling them out which sometimes leads to EASY breakage. http://s1185.photobucket.com/albums/z341/wardog10/?action=view¤t=DSCN9273.jpg Edited January 25, 2012 by wardog Quote Link to post Share on other sites
wardog Posted April 11, 2012 Author Share Posted April 11, 2012 (edited) Haven't posted in a while as i've really tried concentrating on building the model. Here are a few "bad" pics of the RAT bay and the incomplete turbine assembly. Still have a ways to go on these as i haven't touched them in a long time. Been working on the cockpit finally and should have some pics soon. Edited April 11, 2012 by wardog Quote Link to post Share on other sites
VA-115EFR Posted April 11, 2012 Share Posted April 11, 2012 HE'S BAAAAACK!!!! Bring on the updates!!! RAT turbine looks great! Quote Link to post Share on other sites
twhite80 Posted April 11, 2012 Share Posted April 11, 2012 Unbelievable work! I have been building since I was 6 and there is no way I could do anything like this! Amazing! Keep going and show us more! Quote Link to post Share on other sites
wardog Posted April 12, 2012 Author Share Posted April 12, 2012 Found a few better pics of the stuff previously posted along with a few other things.A lot of this stuff is still to be completely finished but I'll probably wait until I get closer to the end of the build. Quote Link to post Share on other sites
JesniF-16 Posted April 12, 2012 Share Posted April 12, 2012 Wow, I guess there is no limit to how much detail a person can add!!! Nice work /Jesse Quote Link to post Share on other sites
tom-navy-cat Posted April 12, 2012 Share Posted April 12, 2012 when i see this i want to take up another hobby....unbeleiveable workmanship Quote Link to post Share on other sites
mareku Posted April 13, 2012 Share Posted April 13, 2012 Wow! This is a realy great build More please Quote Link to post Share on other sites
dkobayashi Posted April 15, 2012 Share Posted April 15, 2012 Glad to see this still going, so awesome! My A-6 has been sitting on the backburner... Quote Link to post Share on other sites
VA-115EFR Posted April 15, 2012 Share Posted April 15, 2012 I'm STILL convinced Wardog used to build Intruders for Grumman! Simply a work of art! Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.