ESzczesniak Posted November 29, 2017 Share Posted November 29, 2017 I'm moving to a new house and am going to have a legitimate man cave finally. A big part of this was including a dryer vent/pipe outside for a spray booth. I've been looking at the Artograph 1530 and Paasch HSSB-30-16. I was wondering if anyone had some input. These are the thoughts I've had so far: Artograph 1530: I like the downdraft design and the clear top to let more light in. I'm not such a fan of having to change proprietary carbon filters yearly(ish) and the filter paper. It's also 370 cfm between the 2 fans and I will have a 10-15 foot run with 3 90 degree turns by the time it gets outside to the dryer vent. Paasche HSSB-30-16: Looks rugged, I like the more generic filter. The fans are 540 cfm, so I wonder if they are better suited to my run. Not such of fan of needing to mount extra lights inside. Any thoughts or other recommendations? Thank you! Quote Link to post Share on other sites
David Fifer Posted November 29, 2017 Share Posted November 29, 2017 I don't have any experience with the Artograph or Paasche, but here are a couple more options to consider if you haven't already: http://pacepaintbooths.com/pace/Products.htm https://vent-works.com/blogs/the-ventilation-blog/15945741-diy-hobby-spray-booth After studying everything I could find online about all four, I decided to give the Vent Works DIY booth a go. I've got all the parts in my garage (they look good) but won't get around to building it for another month or two. All brands seem to have different pros and cons as you note. At the end of the day I suspect any would work fine. Quote Link to post Share on other sites
ytsejam87 Posted November 29, 2017 Share Posted November 29, 2017 If you are handy beyond modeling, take a look here for an idea for a DIY: https://vent-works.com/blogs/the-ventilation-blog/15945741-diy-hobby-spray-booth. I actually built my spray booth last year, out of mdf, then saw the above video and took their advice and bought the fan. materials were total under 140.00. Quote Link to post Share on other sites
Peaches_Sabrina Posted December 2, 2017 Share Posted December 2, 2017 My $.02 the Artograph would be the better choice the reason being is that fumes are heavier than air, and the Artograph has the fan at the bottom. Why not use the properties of what you are sucking out to work with you than against you. Quote Link to post Share on other sites
SBARC Posted December 2, 2017 Share Posted December 2, 2017 For anyone that doesn't have room or funds for a spray booth....the kitchen rangehood works great.....just protect the area from any overspray and do your painting when your lady is out at work etc. Be careful if you have a gas stove with pilot lights and you plan to use a cardboard box for the spray booth overspray under your rangehood. Just use common sense to keep things safe. Quote Link to post Share on other sites
Joel_W Posted December 17, 2017 Share Posted December 17, 2017 I'm in the process of researching a proper spray booth that vents through a window with a vent kit. But for years I've been using my homemade one with complete success. I purchased from Walmart a desktop box type fan that would just fit into the bottom of a large storage bin that fits the model room window. I cut out the bottom so the hole was slightly smaller then the fan, drilled four holes and using wire crisscrossed, I secured the fan. I just place the unit into an open window against one side, and pull the window down to secure it. I bought some rigid insulation that I cut to fit the opening left that seals off the cold/heat, and keeps the bugs out. Just mount the fan so that it exhausts air out not sucks air in. I've been using a clip on light to illuminate the inside when I air brush. As for a filter, to be perfectly honest, I've never used one, and the fan still works just fine. When I've messed up the inside too much from paint, I remove the fan, and clean it with lacquer thinner on a rag, then wipe it dry. I've yet to replace either the bin nor the fan. The only issue is that I did remove the window screen so you really can't leave the window open in the nice weather. Joel Quote Link to post Share on other sites
JesusNut Posted December 18, 2017 Share Posted December 18, 2017 8 hours ago, Joel_W said: I'm in the process of researching a proper spray booth that vents through a window with a vent kit. But for years I've been using my homemade one with complete success. I purchased from Walmart a desktop box type fan that would just fit into the bottom of a large storage bin that fits the model room window. I cut out the bottom so the hole was slightly smaller then the fan, drilled four holes and using wire crisscrossed, I secured the fan. I just place the unit into an open window against one side, and pull the window down to secure it. I bought some rigid insulation that I cut to fit the opening left that seals off the cold/heat, and keeps the bugs out. Just mount the fan so that it exhausts air out not sucks air in. I've been using a clip on light to illuminate the inside when I air brush. As for a filter, to be perfectly honest, I've never used one, and the fan still works just fine. When I've messed up the inside too much from paint, I remove the fan, and clean it with lacquer thinner on a rag, then wipe it dry. I've yet to replace either the bin nor the fan. The only issue is that I did remove the window screen so you really can't leave the window open in the nice weather. Joel Joel, do you have any pictures of your setup? This sounds like an easy way to go about it without a bunch of cost. I'd rather spend the money on kits and buts to make the kits better. Quote Link to post Share on other sites
AnthonyWan Posted December 18, 2017 Share Posted December 18, 2017 I've got an Artograph 1530. No complaints, only praise for it. Clear top is handy too, I mounted a light behind and it provides excellent light for my paintwork. Small problem? Filters are a little expensive but do last a while depending on how much you spray. -Anthony Quote Link to post Share on other sites
tosouthern66 Posted December 21, 2017 Share Posted December 21, 2017 On 11/28/2017 at 9:17 PM, ytsejam87 said: If you are handy beyond modeling, take a look here for an idea for a DIY: https://vent-works.com/blogs/the-ventilation-blog/15945741-diy-hobby-spray-booth. I actually built my spray booth last year, out of mdf, then saw the above video and took their advice and bought the fan. materials were total under 140.00. How does the fan do? I have a booth I made that has a 300cfm fan and it doesn't seem to be pulling enough. I have over spray floating around in the booth at 18psi Quote Link to post Share on other sites
ytsejam87 Posted December 22, 2017 Share Posted December 22, 2017 14 hours ago, tosouthern66 said: How does the fan do? I have a booth I made that has a 300cfm fan and it doesn't seem to be pulling enough. I have over spray floating around in the booth at 18psi I guess it depends on the size of booth. I have to spray into the booth, but I have no issues. My booth is 20" wide, and "12 inches tall, with the fan on top of the booth. my exhaust run is less than 8 ft from booth to outside of the basement, with two 90 degree turns. I am running (at the moment) tamiya paints with mr color leveling thinner with no issues. I do recall someone recommending to use the cheapest filter available, to allow the airflow to be as efficient as possible, as those cheap filters are the least restrictive. To troubleshoot, you might want to disconnect from your vent pipe, and using some type of candle, check to see if the pull is adequate, possibly showing that your ventwork might be restrictive. I would also, at that point try it (with candle) without any filter in place. In my opinion, this would be the least restrictive your vent could be, so if the pull is good, then the problem isn't the hood or fan. Quote Link to post Share on other sites
Robert S Posted January 1, 2018 Share Posted January 1, 2018 The 1530 is awesome. Have had it for 10 plus years and can’t imagine not having a different one Quote Link to post Share on other sites
Mr Matt Foley Posted January 2, 2018 Share Posted January 2, 2018 I love my 1530 also. Whenever the tundra thaws I'm going to permanently vent it through the wall. Right now I have to open a window and vent the hoses outside. Quote Link to post Share on other sites
Robert S Posted January 2, 2018 Share Posted January 2, 2018 I use these so I don’t have to open the window that much to vent it https://www.rcjaz.com/mrhobby-gsigt03e-vent-attachmentair-duct-for-gt03-mrsuper-booth-p-90068769.html Quote Link to post Share on other sites
Mr Matt Foley Posted January 2, 2018 Share Posted January 2, 2018 12 hours ago, Robert S said: I use these so I don’t have to open the window that much to vent it https://www.rcjaz.com/mrhobby-gsigt03e-vent-attachmentair-duct-for-gt03-mrsuper-booth-p-90068769.html That's a great idea. Are they the same diameter as a standard dryer hose? If smaller it will not be as efficient with the air flow and cause less "suction in the booth. Quote Link to post Share on other sites
Robert S Posted January 2, 2018 Share Posted January 2, 2018 They are smaller but I have not noticed any issues. Here is a photo of my attachment (assuming it works) https://photos.app.goo.gl/nCFsnVrASZIyV7fh1 Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.