Jump to content

1/72 Maritime Lift-Span Bridge


Recommended Posts

  • Replies 94
  • Created
  • Last Reply

Top Posters In This Topic

Added wiring harness to console control panel. Since it is the underside (not easily seen) it was pointless to dressed it up.

 

TEaNmxP.jpg

 

Connected control panel and harness to console.

 

GA1jdvw.jpg

 

Made small harness between terminal strips and the two D-Connectors to the back of console (these connect to control box under display table).

 

YXcP6Cp.jpg

Link to post
Share on other sites

Added Passive Infrared (PIR) sensor for detecting any museum visitors approaching the display.

 

DH8hDvO.jpg

 

Dyed some felt a grey color and lined the console edges of front panel.

 

zWYEMeD.jpg

 

Drilled holes in the thick Perspex, allowing heatwaves to reach the PIR sensor. A portion of the front panel was used as a kick board to protect the Perspex.

 

7tF4G3U.jpg

Link to post
Share on other sites
9 minutes ago, Slartibartfast said:

You are cranking this out post haste!  Was the IR sensor your idea or part of the original plan?

Hello Bruce.

 

As mentioned earlier, I am posting daily to catch up to where I am at the moment with the project. Then my posts will be less frequent.

 

The IR sensor was in the back of my mind not long after the console was to be a wiring diorama. It was after the harness got installed, and near its completion as a wiring diorama, that I bought the PIR unit.

Link to post
Share on other sites
1 hour ago, Slartibartfast said:

Oh, please don't make me use my memory.  Mistakes will be made.

You and I both my friend.

And if I sit for too long, rigor mortus starts to set in. Man it can hard to stand up again.

Link to post
Share on other sites

The PIR sensors movement in its vicinity. When it does it will turn the console lighting on. The only times it turns off is when the PIR no longer sensors movement for 10 seconds, or when someone starts working the console.

 

LtmqOTI.jpg

 

DjjGs8g.jpg

 

9uOmqAO.jpg

Link to post
Share on other sites

Thank you @Slartibartfast for the spiff.

________________________________________

Now that the wiring diorama is basically completed, I can forget about that part of the project.

At this stage I started thinking about the landscape. That is, the river bank areas.

Here is the North side. My first objective was the staircase, and build from there.

 

cq7Vhos.jpg

Above: 7 years between these two photographs.

 

h6G41rm.jpg

 

Created footpath under the bridge and up the hill.

WAZEfea.jpg

Link to post
Share on other sites
2 hours ago, Slartibartfast said:

You going to have a U-boote navigating under the bridge?

Ha ha ha. No my friend. It's always nice to get a response from you. I am explaining why I won't reply anymore until I get a response. It's an exchange of faviours...Quid pro quo.

Here is my funny reply to your question.

veI5sup.jpg

 

Link to post
Share on other sites

5nPh0Kc.png

 

Late last year the shire council put in a new pathway along Bridge Street. I decided to add this new landscaping to the diorama.

8fgjMft.jpg

 

Xh0OTkr.jpg

 

Took photographs and measurements. Then started building the new pathway.

Kxh0xBK.jpg

 

Rohtg6I.jpg

 

YBNqL3Y.jpg

 

baKzB5e.jpg

Link to post
Share on other sites
  • 3 weeks later...

Thank you @Silenoz for responding.

8 hours ago, Silenoz said:

looking really good... that pathway must be a tedious work to place all those planks one by one...

Yes and no.

Yes, when considering the task as a whole; and no, when considering the one straight matchstick that needs to fit in that spot.

 

As you already know:

If I worry about the whole task, I lack the consideration for that matchstick and end up botching the whole task.

If I focus just on the proceedures of matching the matchstick, one at a time, the whole task will take care of itself.

When I finish the task, I adjust my focus on the whole task and end up saying exactly what you said, "looking really good".

 

That's what we love about modelling. We come to the stages of our tasks and say to ourselves "that's looking good, let's carry on".

Link to post
Share on other sites
1 hour ago, Slartibartfast said:

I am continually impressed by your materials use.

Are you an armor modeller!

Thank you Bruce for compliment.

No, I am not an armor modeller. This bridge project is my very first model.

I think scratch-building lends itself to wondering how and what to use that will simulate what is needed. After all, the parts are not available like a kit provides.

Also I never ever say "that's impossible", so I am compelled to look for solutions.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...