Jump to content

Bought it, so I'll have to build it. - 1/48 Hawker Hunter - Completed


Recommended Posts

Hello everyone,

 

I heard news that Airfix is coming up with a new tool hunter.

https://www.airfix.com/uk-en/shop/new-for-2018/hawker-hunter-f6-1-48.html

 

 So I guess it's time that I build the one that I have before I get tempted to buy the Airfix kit.

 

lx0e3Ae.jpg

 

According to Scalemates, it was originally molded by Academy in 1997 with this boxing released by Italeri in 2012.

There are many short comings and inaccuracies with this kit but I'll only be addressing a few.

 

I bought the SBS detail set which included a replacement cockpit, wheels and main gear wells.

 

bkAgulc.jpg

 

As you can see, both the kit's seat  and cockpit are undersized.

 

CE0ZazF.jpg

 

1REI8qN.jpg

 

Here we have the resin cockpit mocked up. I used the kit's rudders because the resin set didn't provide any.

 

1A66AVI.jpg

 

I've never been much of a wheel well person but I'll use the resin since they were included in the box.

 

GeCTmXj.jpg


They were troublesome to install but look the part once in place.

 

nDT0oMA.jpg

 

lZNiicK.jpg

 

The weakest part of the kit in my opinion are the intakes. Too many pieces with vague attachment points that also fit badly.

Very fiddly and test fittings showed that they will be a challenge. Horribly engineered. 

 

I started out with these 2 halves reinforced with styrene because the joints were so weak.

I made these sanding sticks with toothpicks and 3m sanding sponges stuck together with superglue.

This is round one of many. Putty, sand, repeat.

 

mkiObyq.jpg

 

The squared off intakes needed to be rounded off to look closer to the real thing.

 

2DoU3m4.jpg

 

8QhpmBZ.jpg

 

Here the wings were glued on but the fuselage halves are just taped together.

Some sink marks on the top of the wings have been puttied.

 

WixP3P3.jpg

 

That's all for now folks. Thanks for dropping by.

 

 

 

 

 

 

Edited by CaptainObvious
Link to post
Share on other sites

 

Thanks for dropping by Scooby. Believe it or not, I'm still working on the intakes.

 

On ‎4‎/‎23‎/‎2018 at 4:07 AM, Scooby said:

I should add, a friend of mine bought 1/2 dozen flying Hunters about 10 years ago.

They were the Northern Lights, I’m not sure why they are named now.

 

Your friend bought six 1:1 scale flying Hunters?
And made an acrobatic team no less?
Holy cow!

Link to post
Share on other sites
1 hour ago, CaptainObvious said:

 

Thanks for dropping by Scooby. Believe it or not, I'm still working on the intakes.

 

 

Your friend bought six 1:1 scale flying Hunters?
And made an acrobatic team no less?
Holy cow!

 

Ex-Canadian fighter pilot, training middle-east fighter pilots, he is rolling in the dough. He has a Castle in Saudi, drives a 911. It’s a house but looks like a castle.

Link to post
Share on other sites
On ‎5‎/‎1‎/‎2018 at 7:28 AM, Scooby said:

 

Ex-Canadian fighter pilot, training middle-east fighter pilots, he is rolling in the dough. He has a Castle in Saudi, drives a 911. It’s a house but looks like a castle.

 

Wow. 6 hunters, a 911 and a castle.
I'd say your friend did well for himself!

Link to post
Share on other sites

Hello again everyone.

 

I've been beating the intakes into submission. Here are the interior bits sanded and painted.

Lj3jUkS.jpg

 

The instructions would have you build up the intakes as a completed assembly but I elected install them separately to minimise external gaps.

X1WnFDD.jpg

9FrAba7.jpg

 

I tried out this Vallejo putty as I was told you could wipe it off with water.

IEQp7dc.jpg

It behaves like a rubbery caulking. I haven't been able to get a smooth result with sanding. It will crumble and chunks will come off.
But if you use it like caulking and wipe it off while wet, it will not affect the underlying paint. It does shrink significantly though.
 

So back to regular putty and repaint.

gwpWe0D.jpg

HjXksD6.jpg

 

Not perfect but good enough for me.

upzESUL.jpg

 

The hunter's cockpit is painted black but I used XF-63 german grey instead.

s5M2pJ3.jpg

 

The actual cockpit's switches are mostly black too but I used some artistic license to add visual interest.

BTLoQVd.jpg

 

One last shot before I close her up.

BVpIJPt.jpg

 

I gave the new Quick Setting extra thin a go.

You use it the same way as the regular extra thin except you don't have to hold the parts together as long.

b6pZmhb.jpg

I'm glad I didn't use black for the cockpit. Even in dark gray, you can't see anything. :doh:

 

Thanks for dropping by everyone.

Edited by CaptainObvious
Link to post
Share on other sites

Wow looks just great. Very nice job on those intakes. I like the way you worked on them and got to remember that when I do mine. After seeing yours I think I will do my Academy kit. I just saw that SBS set recently too so it is nice to see it being used and how it fits.

Link to post
Share on other sites
On ‎5‎/‎3‎/‎2018 at 5:40 AM, skyhawk174 said:

Wow looks just great. Very nice job on those intakes. I like the way you worked on them and got to remember that when I do mine. After seeing yours I think I will do my Academy kit. I just saw that SBS set recently too so it is nice to see it being used and how it fits.

 

Thanks Chris. Those intakes were a bear. There are still gaps but I've decided to call it a day and move on. The SBS set, like most resin parts take a bit of fiddling to fit but all in, not too bad.

 

On ‎5‎/‎3‎/‎2018 at 9:45 AM, Slartibartfast said:

Thanks for making this lesser-known Fifties jet a WIP.  I've already learned some things.

 

Thanks for stopping by Bruce. I've learn so much from this place that I am happy I can contribute too!

 

On ‎5‎/‎3‎/‎2018 at 1:49 PM, Sebastijan said:

Excellent progress! Really like how you're beating this kit into submission!

 

Thanks Sebestijan! Is stubbornness a virtue? Cos my wife says no.

 

15 hours ago, Aigore said:

Gorgeous work, really like hos you are elevating that old kit to new hights! 😄

 

Thanks Janne! Very nice of you to drop by. There's lots of rescribing to do now that I at the putty and sanding stage. I'm absolutely hopeless at rescribing.
I use tape guides and my lines still wander all over the place. :doh:

 

Link to post
Share on other sites
5 hours ago, CaptainObvious said:

 

Thanks Janne! Very nice of you to drop by. There's lots of rescribing to do now that I at the putty and sanding stage. I'm absolutely hopeless at rescribing.
I use tape guides and my lines still wander all over the place. :doh:

 

Are you using dymo tape? Dymo tape is thicker and a better support for a scriber than ordinary tape.

Link to post
Share on other sites

I just caught up with this build Captain.  Great job on the intakes and for even starting this build in the first place!  I cannot overcome the temptation to build the new tool kits of aircraft I have in the stash.  EBay is my friend.  Ha!

 

Steve

Link to post
Share on other sites

Capt. Obvious,

 Sorry I'm late to your party, but with the warmer weather, I'm actually spending more time outdoors these days. 

  Excellent work in the cockpit. Your decision to go with Dark German Gray really makes a huge difference.  

 the intakes are coming alone quite nicely. As for the Vallejo putty, I use it all the time for little fill jobs or in areas that I can't get into and sand. I apply just enough to cover the joint, then give it 30 seconds to settle, then with a damp Q tip I very lightly go over the joint trying to work across it rather then going down it if possible. I make sure that I've cleaned the sides of the joint. As you found out it really shrinks, so I repeat several more times. eventually it will level off. Another great use for it is a small seam after painting and you don't want to go the sanding process. 

 

Joel

Link to post
Share on other sites
On ‎5‎/‎5‎/‎2018 at 4:03 PM, Aigore said:

Are you using dymo tape? Dymo tape is thicker and a better support for a scriber than ordinary tape.

 

I tried Dymo a long time ago but I found that the adhesive didn't stand up to repeated use. What I'm using now is triple stacked masking tape which I cut with a penknife and a ruler to get a straight edge.
I may have to give dymo another try.

 

On ‎5‎/‎6‎/‎2018 at 4:23 AM, Falconxlvi said:

I just caught up with this build Captain.  Great job on the intakes and for even starting this build in the first place!  I cannot overcome the temptation to build the new tool kits of aircraft I have in the stash.  EBay is my friend.  Ha!

 

Steve

 

Thanks Steve. What a coincidence! I think we may have a common friend. :cheers:

Link to post
Share on other sites
On ‎5‎/‎7‎/‎2018 at 2:35 AM, Joel_W said:

Capt. Obvious,

 Sorry I'm late to your party, but with the warmer weather, I'm actually spending more time outdoors these days. 

  Excellent work in the cockpit. Your decision to go with Dark German Gray really makes a huge difference.  

 the intakes are coming alone quite nicely. As for the Vallejo putty, I use it all the time for little fill jobs or in areas that I can't get into and sand. I apply just enough to cover the joint, then give it 30 seconds to settle, then with a damp Q tip I very lightly go over the joint trying to work across it rather then going down it if possible. I make sure that I've cleaned the sides of the joint. As you found out it really shrinks, so I repeat several more times. eventually it will level off. Another great use for it is a small seam after painting and you don't want to go the sanding process. 

 

Joel

 

Hi Joel,

 

A big welcome! The party just got started.

Great advice on using Vallejo putty. After your clear and concise tips, I will definitely give it another try. 
I'm of the opinion that any tool is a good tool. You just have to find the correct way of using it. 
Thank you! 

Link to post
Share on other sites
3 hours ago, CaptainObvious said:

 

I tried Dymo a long time ago but I found that the adhesive didn't stand up to repeated use. What I'm using now is triple stacked masking tape which I cut with a penknife and a ruler to get a straight edge.
I may have to give dymo another try.

 

Dymotape has two strips to remove on the adhesive side, I usually remove one strip and use until the adhesive is gone and then I remove the other strip and use the other half of the adhesive side...makes them last a bit longer.

Link to post
Share on other sites

Capt. Obv. 

  One  guide I usually forget about way to often is Electrical tape. Not because it doesn't work, but because I  never remember to buy a 2nd or 3rd roll just to keep with my modeling supplies. The advantage to electrical tape is that it's thicker then masking tape so you don't need to double or triple it up, it stretches and stays stretched as long as it's tacked on to a surface,  it's much tougher then masking tape so a slight wiggle of your scribing tool won't cut into it, and like Tamiya's curvable tape it just puts plain masking tape to shame when you need it to conform to concave or convex shape.

Joel

 

Link to post
Share on other sites
On ‎5‎/‎10‎/‎2018 at 5:20 PM, Aigore said:

Dymotape has two strips to remove on the adhesive side, I usually remove one strip and use until the adhesive is gone and then I remove the other strip and use the other half of the adhesive side...makes them last a bit longer.

 

That's interesting. The ones I get only has one strip to remove. Gives me an idea though, I can lightly score the strip to make 2 halves. Or I can stick in onto masking tape and see if that works better.

 

On ‎5‎/‎10‎/‎2018 at 9:28 PM, Joel_W said:

Capt. Obv. 

  One  guide I usually forget about way to often is Electrical tape. Not because it doesn't work, but because I  never remember to buy a 2nd or 3rd roll just to keep with my modeling supplies. The advantage to electrical tape is that it's thicker then masking tape so you don't need to double or triple it up, it stretches and stays stretched as long as it's tacked on to a surface,  it's much tougher then masking tape so a slight wiggle of your scribing tool won't cut into it, and like Tamiya's curvable tape it just puts plain masking tape to shame when you need it to conform to concave or convex shape.

Joel

 

 

Great idea. I'll give that a try too. I've tried using Tamiya's flexible tape and I found it to be useful in curves. But it doesn't stand up to repeated applications. U get maybe 2 or 3 placements out of it. Electrical tape may work better.

 

Link to post
Share on other sites
5 hours ago, CaptainObvious said:

 

That's interesting. The ones I get only has one strip to remove. Gives me an idea though, I can lightly score the strip to make 2 halves. Or I can stick in onto masking tape and see if that works better.

 

 

Great idea. I'll give that a try too. I've tried using Tamiya's flexible tape and I found it to be useful in curves. But it doesn't stand up to repeated applications. U get maybe 2 or 3 placements out of it. Electrical tape may work better.

 

 

Capt. Obvious,

   I've  never tried to use Tamiya Flex tape more then once. didn't even know you could. I just treat it like Tamiya tape. The only difference is that I only use it for jobs that the regular stuff can't or won't handle.

Joel

Link to post
Share on other sites
  • 2 weeks later...
On ‎5‎/‎15‎/‎2018 at 11:05 AM, egg2012 said:

I had similar experience when using that plastic putty.Maybe I applied it in wrong place.Now I use gaianotes m-03r,it works fine.

beautiful cockpit painting.

 

 

Thanks for dropping in Egg2012.
I might have to look into Gaianotes m-03r.

Link to post
Share on other sites

Hi all,
 

Time for a quick update.

The kit's canopy is designed to be closed with no provision for opening it. However I couldn't let that resin cockpit go to waste under a closed canopy.

Aftermarket vacuum formed canopies are available but I decided to go cheap.

 

The area behind the cockpit was too wide for the canopy to slide aft. I thinned it down about 1.5mm.

jPexyIL.jpg

 

I thinned the canopy a little too where it contacts the fuselage. This allowed it to be placed without stressing the part.

QRIES37.jpg

 

The canopy comes molded with an aft frame not present in the actual aircraft. When installed in the closed position as designed, it is not obvious.

G3INyx0.jpg

 

However as I wanted the canopy open, the frame had to go. Some filing, sanding and a dip in future later, viola!

D6WnpSd.jpg

 

I'm not sure why the designers placed the ejector pins on the side with all the nice rivet detail when the other side is blank and flat.

JaWYznf.jpg

 

Pin marks gone, along with all that nice detail. I used some tape on the landing gear struts to match the bigger holes in the resin wheels.

XAs1A1e.jpg

 

I've decided to do the Singapore scheme and they were modified to carry sidewinders. I had to scratch up some rail adaptors as none were included in the kit.

The sidewinders and launch rails were leftover from the Tamiya tomcat build while the fuel tanks were included in the kit.

rHzYvCm.jpg

 

So here we are.

L3928uU.jpg

 

Most of the basic construction is complete. I should be able to start painting soon.

ENV7CRZ.jpg

 

Thanks for dropping by everyone. :wave:

Edited by CaptainObvious
Link to post
Share on other sites

Capt. Obvious,

  That's some really nice work on the canopy.  the end results more then justify the effort to produce it.  Great progress as it sure looks like you're nearly ready for primer.

Joel

Link to post
Share on other sites
  • CaptainObvious changed the title to Bought it, so I'll have to build it. - 1/48 Hawker Hunter - Completed

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...