Jump to content
ARC Discussion Forums
john53

Canadair Sabre 6 --- 1/72 Hobbycraft kit

Recommended Posts

Posted (edited)

I am now able to restart this project too. I was missing the slats but just

found a kit that has the slats as extras, Hobbycraft kit 1361 is a hard edge

F-86F but for some reason they left the slats on the sprue. I wanted to do

a hard edged Sabre and this kills 2 birds with one stone so to speak. I am

almost ready to paint this, I was going to use the Hobbycraft Golden Hawk

kit decals but it is looking so good I may get a better set. I scratch built the

scoops on the fuselage by the wing trailing edge.---John

UklgKZZ.jpg

eaGzeOP.jpg

oCr6UBq.jpg

Edited by john53
grammar error

Share this post


Link to post
Share on other sites

There is one other small problem I had. The kit has the drop

tanks in the wrong location. I was informed by a rather smart modeler,

from Canada, that all Sabres, Canadair and North American have

their drop tanks at station 99, which means they are 99 inches from

the fuselage center line to the center line of the wing pylon which holds

the drop tank. He told me ALL model companies made the same mistake

with the exception of Revell's F-86D, according to him it's the only kit of

an F-86 with the drop tanks in the correct location. Just a little tid bit you

may want to check out. The "inner" pencil lines in the photo above are where

I redrilled for that correct dimension.---John

Share this post


Link to post
Share on other sites

My Hobbycraft kit came in, F-86F-25/30. It is a hard wing with a wing fence

but HC left the slats on the sprue, so I can use the slats for the missing ones

on my Sabre 6 Golden Hawks. Also HC has the correct decals for The Huff!

It has the 2 little characters and the Miss Jenny that go on the right side, also

the dragon on the left side has the right colors! I did the Airfix new F-86 and

the colors were off and no right hand side decals, I'll save these and do The

Huff again someday.Looks like HC came through big times for me. Now to

mask the wing for the silver and also do the slats.---John

BaYx9FS.jpg

LR9K4Zs.jpg

Share this post


Link to post
Share on other sites
Posted (edited)

Slats sprayed Tamiya silverleaf, I placed them on the wing for a test

fit, need to straighten them slightly, very minor bow. Time to order the

gold paint.---John

HXW5fBX.jpg

 

Edited by john53

Share this post


Link to post
Share on other sites

Coming on very nicely John, I'll be keen to see the the gold go on.

Steve.

Share this post


Link to post
Share on other sites
Posted (edited)

Thanks Steve, I just added shoulder harnesses and lap belts, I will be

ordering the gold paint this week.---John

2Ky9c1x.jpg

Edited by john53

Share this post


Link to post
Share on other sites

I added the drop tanks, masked then sprayed it Tamiya gold,

rattle can TS-21.---John

fpOiKRh.jpg

bkHxRCa.jpg

Share this post


Link to post
Share on other sites

I did some touch up around the cockpit, canopy rails and gun sight. I

still have the silver on the tail, stab leading edges, around the nose intake

and the tip of the drop tanks.---John

fqYS47g.jpg

Share this post


Link to post
Share on other sites

I masked for the black on the anti glare panel on the nose. It woud

be easier with an air brush but not having that set up I masked with

Tamiya tape and cling wrap. Should do the trick.---John

bXyS4RM.jpg

Share this post


Link to post
Share on other sites

Masks are off, not to awful shabby. I still have to mask for the nose ring and

 tail-stabs leading edges for the silver---John

iL9USaL.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×