Jump to content

Bf109E-3 "WEISSE 5" Obfw. Jakob Arnoldy, Mandal 1940 (Tamiya 1/72)


Recommended Posts

Hi all

This is my next project. The kit is the Tamiya Bf109E-3.

My intention is to make one of the decal options for the aircraft flown by Obfw. Jakob Arnoldy. He was attached to 4./JG77 based on Mandal in 1940. During that time he was flying the "Weisse 5"which was a Bf109E-3 WNr.1276. The painting scheme is RLM71, RLM02 over RLM65 which was characteristic of the period.

Messerschmitt-Bf-109E3-4.JG77-White-5-Jakob-Arnoldy-WNr-1276-Norway-Apr-1940-01.jpg

Bf109E-3 "Weisse 5" Wnr. 1276, Obfw Jakob Arnoldy, Mandal September 1940

Bf-109E3-4.JG77-%2528W5%252B-%2529-Jakob-Arnoldy-WNr-5277-sd-by-RAF-33Sqn-John-Mackie-15th-Apr-1941.jpg

Here is a shot of his another "White 5" being also the E-3 type. It seems to be the kite he was shot down. Believing the caption it's Bf 109E3, 4.JG77, WNr 5277 shot down by RAF 33 Sqn, John Mackie, on the15th April 1941.

 

The kit:

 

0001.jpg

 

 

This kit is quite simple and inside the box you'll find one grey sprue with all major parts for assembly, one clear sprue with the canopy parts, decals and instructions sheet.

 

0002.jpg

 

I quickly started by painting the interior with RLM02. In this case I have used Gunze RLM02.

 

0003.jpg

 

0004.jpg

 

0005.jpg

 

0006.jpg

 

Next I started brush painting the cockpit details using Tamiya acrylics.

 

0007.jpg

 

0008.jpg

 

16th August 2018


Some progress done on the cockpit.


Firstly I painted the floor with GUNZE acrylic H70 RLM02 and weathered using water colours pencil silver and Tamiya Panel Accent BLACK.


 

IMG_1435.jpg


Following I worked on the firewall, basic painting to pick up the details using Tamiya XF-63 German Grey for the cannon butt, GUNZE acrylics H8 SILVER for the pedals and GUNZE acrylic H70 RLM02 and weathered using water colours pencil silver and Tamiya Panel Accent BLACK. I added a piece of lead foil for the pedal straps and painted it GUNZE H66 RLM79 to simulate leather.

 

IMG_1434.jpg


 Next I drilled the seat belt aperture and added the seat belts, fiber material seat belts from KAMIZUKURI (870-0906). I'm not sure about the colour though, I'll probably need to paint it. I also weathered it using water colour pencil silver.

 

IMG_1433.jpg

 

The instruments panel was painted Tamiya XF-63 German Grey and than I used the supplied decals. I did added the filter pump control lever made of a piece of photo etch scrap.

 

IMG_1436.jpg

 

21st August 2018

 

Finally re-painted the seat belts, they look better now.

 

IMG_1437.jpg

 

Here is how the cockpit is looking at the moment.

 

IMG_1438.jpg


 

Here is how it looks now, attached to the fuselage

 

IMG_1440.jpg

 

IMG_1441.jpg



06th September 2018


Continuing with the building I decided to make an improvement to the kit by cutting off the wing slats. This is the first time I'm doing this, so bear with me.

 

IMG_1452.jpg

 

IMG_1455.jpg

1st attempt. I had to re-do it. The slats locations were wrong. See photo reference below.

Slats_Me109E-4.jpg

This drawing (thanks Eduardo Brettas for the help) shows exactly where the slats are positioned.

 

 

Asa_-_Bf_109_E_08.jpg

Here is the real deal. The slat is fully extended in the photo above.

 

 

After discovering I had made a mistake with the slats positioning I scrapped it and started again. Here I used a tip I got from a fellow modeller Luftwaffe esperten Mr Brettas (you can find his fine works here: Harpias e Águias da Luftwaffe by E. Brettas ). He told me to glue a piece of fine plastic in the overall extension of the slat, then drill the a hole for positioning the slats openings and cut the excess with a sharp hobby knife. So that's what I have tried to do.

 

IMG_1471.jpg

 

IMG_1472.jpg

 

 


I also worked on the main landing gears, I made the hydraulic brake line out of thin copper wire, it was then painted Gunze RLM02 and Silver. The propeller is very good and it was painted using Gunze RLM70 and Aluminium. I t still needs to be properly weathered..

 

IMG_1453.jpg



One annoying thing about this Tamiya kit is the closed canopy as the only option. After working the beautiful interior it would be insane to keep it closed. So I decided to carefully cut it open. I than polish it and gave a bath of FUTURE to restore the clear.

 

IMG_1454.jpg

 


Getting ready for painting!

 

IMG_1515.jpg

 

IMG_1516.jpg

 

IMG_1517.jpg



Starting the painting adventure, I decided to show a step by step of my (not so conventional) painting method.

It may seen odd, but I don't prime my model, I apply a coat of silver instead. In this case I used GUNZE acrylic H8 Silver, thinned with MLT (1H*:2MLT+retarder) and 3 drops of Mr retarder mild, air pressure at 20psi. I applied it overall and set it to dry overnight.

 

IMG_1519.JPG

 

IMG_1520.JPG

 

After allowing it to dry completely I inspect the model for any imperfections requiring to be fixed. In the photo below you can observe that I sanded on starboard top wing. I than start to pre-shade. Some people say pre-shading is not worth the working. However, I do like it and think it's worth the extra time. Basically I spray very thinned XF1 Black (1XF1:4X20A+retarder) at low air pressure (8psi) in thin lines and in areas I want it to be shadowed. I don't worry about little over spray and not so straight lines since I can correct them later.

 

IMG_1522.JPG

 

IMG_1523.JPG

 

With the pre-shade complete you can start your painting straight away if you wish so.

In this case I'm using Gunze acrylic H67 RLM65 (1H67:3MLT + 3 drops Retarder). The idea is to work by panels, starting with the panel centre and expand it to cover all, controlling the coats to not cover the pre-shade completely.

 

IMG_1524.JPG

 

IMG_1525.JPG

 


Patient is the key here. Don't try to do the whole kit at once. I usually load smaller amounts of paint at a time, that would allow me to do a wing, for example. Then I have to stop, clean the airbrush, re-mix the paint etc to stat over again. This allows to paint to dry and show off the effect, this way you don't over-do it and loose the effect (better control)

 

IMG_1533.JPG

 

 

IMG_1534.JPG

 

IMG_1535.JPG


RLM02 (Gunze H70) and RLM71 (Gunze H71)thinned with MLT.

 

IMG_1556.jpg

 

IMG_1557.jpg

 

IMG_1558.jpg


 I than gave an overall coat of Tamiya X-22 Clear thinned with Mr Levelling Thinner (MLT) at ratio 1 paint: 3 MLT, 15psi.


Decals in place, using the Micro Sol / Set solutions. Tamiya decals are very thick but conform pretty well with Micro Sol.

 

IMG_1569.jpg

 

IMG_1570%2B5.jpg

I didn't use the original Baukenkreuz since the it was different from my references (see first photo on this post). I used one set from FCM decals instead.

 

IMG_1648.JPG

 

 

IMG_1649.JPG

 

Another coat of Tamiya X-22 Clear thinned with MLT (1:3,15psi) was applied and the kit set aside to completely dry before starting with the weathering.


What's the spinner colour? I was pondering about this question for a while. According to the Tamiya instructions I should paint it RLM70 entirely. However, looking to the first photo of this article, you will notice a spinner in lighter colour. 

white5.jpg

The photo cropped and enlarged, observe the spinner colour

I was searching around in different forums and finally got a decisive answer. Please see the photos below of various JG77 on the same period.

Bf%2B109E%2BJG77%2BNorway%2B1940_b.jpg

Observe the aircraft parked in the background

 

Bf%2B109E%2BJG77_.jpg

The colour of the spinner is very clear for the both aircraft

 

Bf-109E3-4.JG77-Trondheim-Norway.jpg

A Bf109E-3 for the JG77 clearly showing the spinner in WHITE while the backplate is RLM70

 

Bf-109E3-Stab-II.JG77-Apr-1940.jpg



So the colours were set to be RLM70 for the bad plate and RLM21 White for the spinner.

IMG_1687.jpg



To be continued!

Link to post
Share on other sites

Continuing with this building. Some weathering has been done using washes and some watercolour pencils. A coat of Gunze H20 Flat Clear has been sprayed overall to allow for some pigments to be applied.

 

IMG_1698.jpg
The Me109 were notorious for the oil leaks and overall dusty

 

IMG_1699.jpg
Port side view showing overall weathering and exhausting stain

 

IMG_1700.JPG
Starboard side view showing overall weathering and exhausting stain

 

IMG_1701.jpg

 

IMG_1702.jpg
Slats in place

 

IMG_1703.jpg
The slats add a nice touch to the model

 


To be continued!

Link to post
Share on other sites

Small parts details being added.

 

IMG_1725.jpg

The propeller and spinner in place. Please note the canon muzzle showing. The antenna mast on the right

 

IMG_1726.jpg

Landing wheels finished. Some Aluminium scratches made with Quilt pencil and some red tags made with watercolour pencil

 

IMG_1727.JPG

Landing gear in place

 

IMG_1728.JPG

Note the brake fluid line loop characteristic of the Bf109

IMG_1730.JPG

 

IMG_1729.JPG

Tail wheel

 

 

IMG_1731.JPG

 

IMG_1732.JPG

 

IMG_1733.JPG



A small setback. When I did take out the windshield masking tape I've noticed some flat clear leaked into the windshield's side panels (sorry! No photos).

I'm trying to fix it up by polishing with Tamiya compound putty.



To be continued!

Link to post
Share on other sites

Problem solved. Apologies for not having the photo of the damaged windshield but hereto is fixed. I've polished it with Tamiya compound putty medium and fine until removed (or most of it), I then gave it a bth on Future Clear and left to dry overnight.

 

IMG_1749.JPG
Sorry about the bad photography but the arrow shows what was left of the stain

 

IMG_1750%2B7.JPG
Same as previous photography remarks

 

Continuing with the building I glued the parts on the fuselage using white glue.

 

IMG_1751.JPG

 

IMG_1752.JPG

 

 

Now is time to paint the frames.

 



To be continued!

Link to post
Share on other sites

Now is time to paint the frames.


For the frames I used clear decal film painted. First painted RLM02 and then RLM71.

I cut 1mm stripes to approximate length of the section. apply as per usual decal methods.

After completing, use Micro Sol to make it conform to the part.

 

IMG_1753.JPG

 

IMG_1754.JPG

 

IMG_1755.JPG

 

 

IMG_1757.JPG

Cut decal stripes of about 1mm and to desired length 

 

IMG_1760.JPG

Here you van see the inside colour showing through on the middle frame

 

IMG_1758.JPG

 

 

IMG_1759.JPG

 

 

 


It is a little bit of a work perhaps, but heaps better than to cut out masks for those complicated canopy frames. The final result is, by far, better than masking.

 

I'm now reaching the final steps of this building. Most probably the next photos will show the completed model.

 

To be continued!

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...