Modelkeenfan Posted August 4, 2019 Share Posted August 4, 2019 Can anyone tell me the differences between the F16D block 30 and a block 50? Thanks Quote Link to post Share on other sites
Dave Williams Posted August 4, 2019 Share Posted August 4, 2019 The Block 30s have the original lightweight gear and flat gear doors. The Block 50s have the heavyweight gear and bulged gear doors. Also, early Block 30s had the small NSI inlet instead of the larger MCID. Quote Link to post Share on other sites
Niels Posted August 4, 2019 Share Posted August 4, 2019 (edited) The small NSI inlet only applied to block 30's up to serial 86-0262 for the C and 86-0044 for the D, after this all GE powered block 30's have the big MCID intake. In addition to the differences mentioned above, you also have minor changes like number of chaff/flare buckets; block 50 have 4 while block 30 have 2-4 depending on production run. Depending on time frame your model is to depict, there has also been various updates like CCIP which moved the landing lights from main LG to nose LG etc. Check out www.F-16.net - this is one of the best online references for F-16's. Edited August 4, 2019 by Niels Quote Link to post Share on other sites
Murph Posted August 4, 2019 Share Posted August 4, 2019 Check here: LINK Regards, Murph Quote Link to post Share on other sites
Modelkeenfan Posted August 4, 2019 Author Share Posted August 4, 2019 Thanks guys for the replies and info. You have helped me greatly Cheers Quote Link to post Share on other sites
Modelkeenfan Posted August 4, 2019 Author Share Posted August 4, 2019 Just one question. Are the tail fins the same on the F16D block 30 and the F16CJ block 50? Im converting a 1/32 Tamiya F16CJ into a F16D block 30 using the academy sufa top half of the fuselage as it fits fine to to the bottom. Half of the Tamiya F16CJ. The air intakes fit as well and the engine and engine cowling. I simply had to cut out the engine cowling from the academy top half fuselage. So the academy kit comes with the large and small air intakes. So its not hard to make a F16D using the academy sufa and the tamiya F16CJ. Thanks guys for any answers Cheers Quote Link to post Share on other sites
Modelkeenfan Posted August 4, 2019 Author Share Posted August 4, 2019 And of course I will have to use lightweight landing gear and I think I'll just sand down the bulges in the wheel cover doors. Quote Link to post Share on other sites
Niels Posted August 4, 2019 Share Posted August 4, 2019 (edited) 20 minutes ago, Modelkeenfan said: Just one question. Are the tail fins the same on the F16D block 30 and the F16CJ block 50? Yes and no, the only difference is that the D doesn't have the small air vent on either side of the base of the tailfin. This is only found on the C. Rest of the tail is the same however. (Talking about parts C24 and C25 in the Tamiya 1/32 F-16C kit) Edited August 4, 2019 by Niels Quote Link to post Share on other sites
Modelkeenfan Posted August 5, 2019 Author Share Posted August 5, 2019 Does anyone think you could could use two black box 1/32 F-16 block 32 cockpit tubs to make a dual cockpit for a F16D? I have all the necessary parts for the two seat cockpit but wondered if they could be joined together. Anyone tried it? Quote Link to post Share on other sites
habu2 Posted August 5, 2019 Share Posted August 5, 2019 The instrument panel, coaming and side consoles in front and rear pits are not the same size and are configured differently. Quote Link to post Share on other sites
Niels Posted August 5, 2019 Share Posted August 5, 2019 I propose you check out the references available on F-16.net. There you can learn everything you need about the different cockpits, F-16A vs. C, B vs D etc. Quote Link to post Share on other sites
Modelkeenfan Posted August 7, 2019 Author Share Posted August 7, 2019 On 8/5/2019 at 10:54 PM, Niels said: I propose you check out the references a avail able on F-16.net. There you can learn everything you need about the different cockpits, F-16A vs. C, B vs D etc. Quote Link to post Share on other sites
Modelkeenfan Posted August 7, 2019 Author Share Posted August 7, 2019 Thanks guys for all the info. Most helpful. With all the F16 variants you almost need a degree in F16 variants and differences. Just one idea I had, does anyone know if the 1/32 Aires F16D cockpit set for the hasegawa kit would fit into my academy F16? I. Converting a 1/32 Sufa into a F16D. Anyone tried it? Quote Link to post Share on other sites
Modelkeenfan Posted August 8, 2019 Author Share Posted August 8, 2019 I was just researching the 1.32 aired F16D cockpit set and I see it was put on the market in 2010. Doesn't anyone know if its out IG production? If so, does anyone have one to sell? Problem is I can use a black box F16C block 30-32 pit for the from pit but but I'd then have then have to use the academy kit rear pit. Obviously thr rear pit would not be as detailed and would not I volve quite a bit of work to bring it up to the same detail. Not really a big problem, but a lot of work and if I could get the 1/32 Aires F16D cockpit set, would save me a lot of work. I have a 1/32 Tamiya F16C Thunderbirds kit and the isracast sufa conversation set. Plus the Isracast large external fuel tanks, isracast pythons. Popeyes, Deliahs, heavy weight landing gear fro. The tamiya block 50. I will use the Academy 500lbs LGBs, ssodewinders and Flightpath ASRAAMS and Isracast targeting pods. So I think this will make a cracker and more accurate Sufa. So I decided to use convert academy Sufa into a F16D aggressors of the 18 TFW I. The black and grey scheme with a jamming pod and training missiles. So I thought making the academy sufa into a F16D would be a good challenging project as the the academy sufa comes with the GE engine and small intake intake as well. So thats where I'm and thus asking all the questions on the F16D to get it externally correct and the cockpit correct. Just lots of small changes I have to make to the sufa externally but I van use a lot of partd off the Tamiya kit like the tail fin ect to get it externally correct as a F16D. So if anyone has do e this project, it would good to here from you if you have made a sufa from the tamiya thunderbirds kit or converted an academy sufa into a F16D. Any help.or advice would be great. Cheers Cheers. Quote Link to post Share on other sites
Modelkeenfan Posted August 8, 2019 Author Share Posted August 8, 2019 Also guys one question. Could I make a F16D aggressor of the 18 TFW with a load out of a sniper pod, with live Bomb munitions and live sidewinders and AMRAAMS? As I assume they also train pilots using live loadouts? Quote Link to post Share on other sites
camus27 Posted August 8, 2019 Share Posted August 8, 2019 No. I don't think I've seen live ordnance on an aggressor. Pilots training with them would be in their own jets. Quote Link to post Share on other sites
Modelkeenfan Posted August 8, 2019 Author Share Posted August 8, 2019 Neils, what small air intake are you talking about on the tail that the D doesn't have? Is it it the little parts 25 And 24 that are just really small air inducts on the right side of the tail? And I assume the tail shape and tail base of the block 30-32 is exactly the same as in the thunderbirds kit and needs no alteration? Quote Link to post Share on other sites
Niels Posted August 9, 2019 Share Posted August 9, 2019 17 hours ago, Modelkeenfan said: Is it it the little parts 25 And 24 that are just really small air inducts on the right side of the tail? Correct, these the D-model do not have. Quote Link to post Share on other sites
Modelkeenfan Posted August 9, 2019 Author Share Posted August 9, 2019 Thanks Niels for all the info. You are obviously very knowledgable on the viper variants and i appreciate you sharing your extensive knowledge with me. Its great to see a community like the model one where everyone helps out and goes out of their way to share info or help fellow forum members. I have just one more question. In relation to the heavy and light landing gear, did this make any real obvious external differences in the wheel bays? It seems I can only find one 1/32 wheel bay set that is designed to fit the academy F16 and its the sufa wheel bay set. Could I use the sufa wheel bay set in the F16D without it showing any real noticeable differences to the wheel bay of a F16D? Plus the sufa wheel bays are only 25 euros posted. So if anyone could tell me, that would be great. My F16 project is now taking shape Quote Link to post Share on other sites
Niels Posted August 9, 2019 Share Posted August 9, 2019 Thanks for the kind words, Modelkeenfan. The strengthened landing gear is not easy to spot by eye only. The strengthened landing gear was accompanied by larger wheels, and it is these that necessitated the need for the bulged gear doors. For a block 30, you don't need the bulged gear doors as they had smaller (narrower) wheels. If you can sand down the kit parts I don't know as I don't build 1/32. but worst case you'll have to reinforce the kit parts on the inside and then sand down the outside. Not sure if you plan for wheels up or down, but this also could affect how much you can reinforce the main landing gear covers on the inside. Quote Link to post Share on other sites
Modelkeenfan Posted August 9, 2019 Author Share Posted August 9, 2019 Yes I will sand down the bulges on the wheel bay doors as I will have the gear down down. So that's not a problem. I just wanted to know there was no obvious differences in the main wheel bay which was easy to see that it was either a heavy landing gear wheel bay or light landing gear wheel bay. But as I understand it, there is no real differences between light and heavy landing gear wheel bays. So if I use the 1.32 aires sufa wheel bay, no one could tell the difference Quote Link to post Share on other sites
Niels Posted August 9, 2019 Share Posted August 9, 2019 I've forgot - the early block 30's have the landing light on the main wheel struts, this was later moved to the front weel strut. Should be easy to re-create, as it is the round lights on the main wheels. Quote Link to post Share on other sites
Modelkeenfan Posted August 10, 2019 Author Share Posted August 10, 2019 Yes good point. I have an extra sprue of the clear parts so shod be easy put the lights on the struts. I can use a lot of stuff from the Thunderbirds kit and I think the lights are on the struts in the Thunderbirds kit as its a block 32. The whole F16D project popped into my head as I bought the academy sufa simply for the baby JDAMS and I bought the Thunderbirds kit when they were still plentiful. Then I bought all the isracast stuff to convert the Thunderbirds kit into a Sufa. So I didn't know what to do with the academy sufa and as it is a two seater, the F16D idea popped into my mind when a couple of weeks ago I saw new 1/32 F16D aggressor decals on ebay and thought the arctic aggressor scheme would look cool as a F16D. However my knowledge on the F16s is not great thus starting this thread. Quote Link to post Share on other sites
Niels Posted August 10, 2019 Share Posted August 10, 2019 If you have the landing gear from the Block 32, you should have everything you need. Quote Link to post Share on other sites
Modelkeenfan Posted August 10, 2019 Author Share Posted August 10, 2019 Yes I think all set. I haven't built an academy F16 before but s few Tamiya ones. I think the tamiya kit is the better kit but the academy kit should come up all right. I'll pit an ACMI on the right wing tip and an AN/ALQ 188 jamming pod on her belly and she should come up alright Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.