Dutch Posted February 4, 2020 Share Posted February 4, 2020 (edited) Does anyone know if there are decals available for the Boeing 367-80 "707" Prototype in 1/144 (or 1/139) scale? I am interested in modeling it. I am aware of the later Boeing test markings [pre Pan Am Delivery] decals, but I am looking for the 367-80 markings. R/ Dutch Edited February 5, 2020 by Dutch add link Quote Link to post Share on other sites
JohnEB Posted February 16, 2020 Share Posted February 16, 2020 Decals aside, I'd be interested in knowing about the model itself as there are a lot of differences between the 367-80 and a 707. Quote Link to post Share on other sites
AV O Posted February 18, 2020 Share Posted February 18, 2020 On 2/16/2020 at 6:36 PM, JohnEB said: Decals aside, I'd be interested in knowing about the model itself as there are a lot of differences between the 367-80 and a 707. You may find what you are looking for in this thread where there is a discussion going on : https://www.airlinercafe.com/forums.php?m=posts&q=11202 Quote Link to post Share on other sites
Dutch Posted February 18, 2020 Author Share Posted February 18, 2020 AV 0, Where can I order one of Kurt's KC-135s? There is no link in the Airlinercafe post. I am a member, but can't remember my pw to log in. K/r, Dutch Quote Link to post Share on other sites
scotty100368 Posted February 19, 2020 Share Posted February 19, 2020 Dutch, Order them here: https://www.authentic-airliners.de/ Scott. Quote Link to post Share on other sites
Dutch Posted February 26, 2020 Author Share Posted February 26, 2020 (edited) Scott, Yes, they all look very nice. The moulding and recessed panel lines look exquisite. The only qualms I have about the Authentic Ailriners kits are the extra length of the inboard pylon trailing edges for A & E models. It looks like he copied the old Revell JT3D pylons. Here are pictures of the Authentic Airliners pylons from the link above. Authentic Airliners 1/144 KC-135A J-57 engines Authentic Airliners 1/144 KC-135E TF-33 engines. Here are two cropped photos of a KC-135A & EC-135C showing the short pylon trailing edges on all four engine locations. KC-135A EC-135C While I am excited about the beautiful kit mouldings, if I am going to pay Euro 65 for a 1/144 KC-135 kit, it needs to be pretty accurate right out of the box. I have several Revell KC-135A kits for $5-$10, several Minicraft KC-135A/E/R kits for $20-$35, and a few Welsh kits for $25-$30. I am well familiar with the peculiarities of each kit and have performed minor-major surgery to make corrections, particularly the Revell kits. For a $5-10 Revell kit, I can live with that. Once I have paid Euro 65 for a 1/144 KC-135, I don't want to have to pay the equivalent of another Euro 15-20 for replacement engines/pylons. Though, I am still considering purchasing a couple of these kits when they become available. R/ Dutch Edited February 26, 2020 by Dutch Quote Link to post Share on other sites
72linerlover Posted February 27, 2020 Share Posted February 27, 2020 21 hours ago, Dutch said: The only qualms I have about the Authentic Ailriners kits are the extra length of the inboard pylon trailing edges for A & E models. It looks like he copied the old Revell JT3D pylons. Here are pictures of the Authentic Airliners pylons from the link above. Dutch, Actually the inboard long pylons feature is typical of the 707 and it could be that Kurt has a single mould for both models. An other point is that the Kurt's long (wrong) pylons of the TF33 are for the outer engines, as you can see in your second pic, where there are also the TC humps. Bye Euge Quote Link to post Share on other sites
Dutch Posted February 27, 2020 Author Share Posted February 27, 2020 (edited) Euge, Yes, if Keith is molding the engines for the 707 kit, then the rear pylon moldings will work. However the front of the JT3C/J-57s would have to be modified with turbo-compressor hoods for the 707 (4x) / 720 (2x). The JT3D engines will work for the 720B and some 707B/C (American Airlines). Otherwise a third TC hood would be required for the vast majority of 707B/Cs. Here is a link the excellent 707 / 720 article on Airliner Cafe by David Hingtgen. As to the KC-135E, I should have chosen a different photo, instead of the EC-135C. The point remains, that the KC-135 pylon trailing edges are short, not long. C-135Bs were delivered with no TC hoods on the TF-33 engines, while the RC-135B was delivered with TC hoods on Engines 1, 2 & 4, as in the EC-135C photo. Because many C-135Bs were modified into EC/RC/WC variants, there are multiple TC hood combinations for engines # 1,2,3,4. When KC-35As were modified into KC-135Es, they received either two, three, or in a couple of cases, four TC hoods. Again, the pylon trailing edges were all short. For KC-135E, I would recommend including four short trailing edge pylons and three TC hood engine faces and two non-TC engine faces. For KC-135A, I would include four short trialing edge plons and all four engine faces "as is." R/ Dutch Edited February 27, 2020 by Dutch add detail Quote Link to post Share on other sites
72linerlover Posted February 27, 2020 Share Posted February 27, 2020 Perfect said, Dutch. That matches with my knowledge. On the modeling side, I'd say that is always easier shortening than stretching, so if you like the Authentic Airliners engines, you'll face an easy task. Bye Euge Quote Link to post Share on other sites
Dutch Posted March 1, 2020 Author Share Posted March 1, 2020 On 2/27/2020 at 2:40 PM, 72linerlover said: Perfect said, Dutch. That matches with my knowledge. On the modeling side, I'd say that is always easier shortening than stretching, so if you like the Authentic Airliners engines, you'll face an easy task. Bye Euge Thanks Euge! As to shortening pylon trailing edges, I am all too familiar with correcting Revell E-3A AWACS pylons, having recontoured over a dozen last year alone. Enough said!🤨😎 Quote Link to post Share on other sites
waltmert Posted March 9, 2020 Share Posted March 9, 2020 (edited) Dutch, back to your original post, did you find anyone who makes 367-80 decals? I will love a set for the horrible Aurora kit. I might use one of Kurt's KC-135's to do the -80. Cross section is almost good enough Edited March 11, 2020 by waltmert Quote Link to post Share on other sites
Dutch Posted March 11, 2020 Author Share Posted March 11, 2020 Walt, No takers yet. Unless someone still has an old ALPS MD-1000 printer. K/r, Dutch Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.