Flankerman Posted April 20, 2020 Share Posted April 20, 2020 Braving the lockdown, my postman Martin has just delivered this new kit from Mikro-Mir Having already built a model of the USS Parche.......... I was going to pass on this new kit - until I realised it represents the pre-stretch early version........ As the boxart shows - the sail is different, she carries a DSRV (as a cover for her covert ops) - and the hull is 100ft shorter..... The shorter hull is is two halves - split horizontally... The only other sprue carries the sail, diving chamber, DSRV and other small parts... The assembly instructions and painting guide is printed on thin A4 paper folded in half... Completing the kit is an etched fret containing the single propeller and DSRV mounting struts plus a small, well printed decal sheet. Another very welcome kit from Mikro-Mir's expanding range of 1/350 scale subs. Nice one MM..... Ken Quote Link to post Share on other sites
Flankerman Posted April 27, 2020 Author Share Posted April 27, 2020 I've made a start. As is usual with Mikro-Mirs limited-run kits, the parts exhibit some flash - quite an amount on this new model and it seems to be getting worse...... After scraping it off, I added strips of plastic card to aid alignment.... Joining the two hull halves reveals a prominent joint line....... .... that needs the application of filler...... The diver lockout chamber is in three parts - again with lots of flash (note the unfettled top piece)...... Quote Link to post Share on other sites
Flankerman Posted April 29, 2020 Author Share Posted April 29, 2020 The lockout chamber assembled.... ... the sides don't fit precisely - leaving a gap at the front end.... The parts for the sail - and its rear extention ........ I may need to buy shares in filler manufacturers.... Ken Quote Link to post Share on other sites
Slartibartfast Posted May 1, 2020 Share Posted May 1, 2020 False economy. You're just earning back money you spent. The trick is to get other people's money. Stop building Mikro-Mir, buy putty stock and then sell Mikro-Mir. Quote Link to post Share on other sites
Flankerman Posted May 2, 2020 Author Share Posted May 2, 2020 Lots of filing/sanding later.... The Lockout Chamber pannier, the hull and the sail.... Diving planes, sonar dome and Towed Array Sonar tube attached... The TAS tube is in two parts -just butt-joined and very delicate - and, guess what? - it needs some filler to blend in the front end!! Almost ready for a primer coat...... Ken Quote Link to post Share on other sites
Flankerman Posted May 6, 2020 Author Share Posted May 6, 2020 In the meantime - the parts for the 'dummy' DSRV.... (it looks more like a torpedo) Tiny parts, lots of flash to clean off, massive sprue gates, no propeller supplied.... what's not to like......??? The instruction diagram shows vertical fins on the aft end of the DSRV - but they have moulded only horizontals - I suggest cutting two of them off to make verticals (guess who didn't?) The model is now painted - Halfords car spray rattle cans - Matt Black, Red Plastic Primer and Volvo Dark Grey..... I managed to break the towed array cable whilst masking..... It's only a weak butt-join - I'll have to try to hold it steady whilst glueing both ends of the part..... Ken Quote Link to post Share on other sites
Flankerman Posted May 6, 2020 Author Share Posted May 6, 2020 PS - I found this image on't tinterweb thingy...... It shows USS Parche as first launched (top), followed by her conversion to 'Special Ops' (and as kitted by Mikro-Mir and finally, after having her hull lengthened by 100ft. My conversion - here - shows how to make the last version. (mine lacks the lower lockout chamber - due to scarcity of info at the time... Ken PS Apologies if I am breaking any rules posting this image....... Quote Link to post Share on other sites
jeffryfontaine Posted November 7, 2020 Share Posted November 7, 2020 There is now a 3D printed conversion now available at [url=https://www.shapeways.com/]ShapeWays[/url] to build the third and final version of the USS Parche (SSN-683) with the hull extension at this link: [url=http://shpws.me/RDuD]ShapeWays > Mulsanne's Model Corner > USS Parche SSN-683 Special Ops version 1/350th scale[/url] Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.