Jump to content
ARC Discussion Forums
konbini

1/48 Hasegawa F-22

Recommended Posts

Good day folks,

 

After a short break after my F-16, I decided to start work on the F-22 from Hasegawa. I was always a fan of the F-22, from the prototype to the current bird.

 

Some back info, my apologies bear with me. Historically my luck with the raptor scale model hasn't been good. Testors released a 1/32 kit of the YF-22 a long while back, and I jumped on it. I  was young and totally new to aircraft scale modelling and I thought a few small bottles of testors enamel, a paintbrush, and some glue (and of course it wasn't the proper styrene glue)  would suffice. I completely bombed it.  My second attempt, in my early teens by then, was the Tamiya 1/72 f-22. That went together mostly alright - pretty average. Only a minor hiccup when I tried to rush glueing the landing gear and putting it on its feet too soon. After spraying a matte topcoat I decided to clean up my desk and set the airplane on a stool. I left for a bit of lunch, but came back to a flattened semi-2D raptor. My mother had sat on the poor airplane. My mother was fine, no worries there, the vert stabs were already set at an outward angle, so they flattened outwards.  Maybe the radar signature reduction worked fabulously. Good lesson in aircraft parking. 

 

Fast forward, surely better luck now.

 

Work started like my previous build, on the bay. My plan is to slowly build up the bay while I work on other areas. I also spent a lot of time sanding down the armour plates on the top and bottom halves of the fuselage. Some guys don't mind it, I happen to think they are a bit overscale. No problem, nothing sand paper and time wouldn't fix. I added some detail to the coaming. 

 

I tried to be as realistic as I could with the weapons bay, though knowing it would be on the under side of the airplane and with potentially missiles blocking part of the view, I am trying to work out a balance. I have so far settled with leaving most of the middle part slightly spartan and sprucing up detail around the outer edge of the bay. Still a WIP.  For the blue cable management things I used strips from a drinking straw, cut to appropriate size. 

 

The ejection seat I decided would be made from the kit parts with a bit of sprucing up via scratch building. I believe this provides best fit and less fighting/fiddling with it. the "sheepskin" texture is made by dabbing on some Tamiya texture paint.

 

Konbini

 

fWmlhm7.jpg

 

YUj8J6L.jpg

 

 

jW2b98j.jpg

 AFUESi5.jpg

 

dRg7jSf.jpg

Share this post


Link to post
Share on other sites

Nice. 

Looking forward to your next updates

 

Kind regards,

 

Robert Jan

Share this post


Link to post
Share on other sites

Always nice to see the Raptor in the WIP. Hope you make it really good. It loks like a nice start, I especially like the cables in the bomb bays. 👍 If I build it one day, I would sand flush all the raised details on the fuselage and scribe them instead. That's just a tip of course. 🙂

Share this post


Link to post
Share on other sites
On 6/18/2020 at 9:17 PM, Gonzales said:

Nice. 

Looking forward to your next updates

 

Kind regards,

 

Robert Jan

Thanks Jan,

Got one coming right up. 

On 6/20/2020 at 8:33 PM, my favs are F`s said:

Always nice to see the Raptor in the WIP. Hope you make it really good. It loks like a nice start, I especially like the cables in the bomb bays. 👍 If I build it one day, I would sand flush all the raised details on the fuselage and scribe them instead. That's just a tip of course. 🙂

Thanks for the comment. Like my last build I'm hoping to leave no stone unturned. Cabling and scratch making makes my head spin and I do hope it will come out nicely. Surface detail wise, for my build it remains to be seen if I can achieve the desired results, I may need to rescribe a few things. This is where I need a bit of luck =D

Share this post


Link to post
Share on other sites
Posted (edited)

Next update, progress in the cockpit.

 

As mentioned previously, I generally stuck with the kit parts for ease of build and fit. I also slapped on eduard's PE bits - they are a big bonus for me, especially the sharp thin angles for the ejection seat rails, where the kit plastic is just a slab of plastic. Some profanity here and there as I tried to fit on the rails extending past the tub, they were a butt fit joint. After some scratch built cables and detail (such as the ribbing around the, er golf club face looking things behind the cockpit/ejection seat), I sprayed the cockpit tub with Tamiya's rubber black. I tried first with priming in straight black and it was dark....   Tamiya's rubber black is a suitable base black for me. The control stick's buttons were just chocolate bar looking things so I cut them off and made actual buttons for the stick. Eye rest after that.

TCIUl81.jpg

 

v3AL8AW.jpg

Next up, I followed my previous build with the same technique, using Eduard's cockpit panel's and sprucing it up with bits and pieces of .15mm wire/styrene rods. Once those are on I carefully, very carefully CAed them onto the tub. 

 

 

The instrument faces I sprayed with rubber black to simulate "off" and I felt this looked a bit more natural. The kit instrument panel didnt include, what I believe are, leg restraint rope/wire so I scratched these out of 0.3mm styrene rods. 

SWQGRYS.jpg

I sprayed the ejection seat, applied decals, weathered it appropriately, and then set it inside the tub. This will be it for today, a good eye shut lest I bust something or do something I regret to the model. 

 

 

Again questions queries suggestions all very welcome. I am looking forward to more progress on this bird. Pics might be in next post as this post encountered the web error message. I'll try again. 

 

 

Konbini

Edited by konbini

Share this post


Link to post
Share on other sites
Posted (edited)

Post 2 for the update:

Unfortunately the forum didn't allow me to further edit the post, I'll post more pictures here. My apologies.

 

wGy9AyR.jpg

 

BFj85jm.jpg

 

CNqEgHY.jpg

 

weAHPDc.jpg

 

4UocEDI.jpg

 

8F05Rbh.jpg

 

c5b0b8b.jpg

 

Konbini

Edited by konbini
previous post web error, picture post here

Share this post


Link to post
Share on other sites

Excellent stuff, just WOW.

 

Kind regards,

 

Robert Jan

Share this post


Link to post
Share on other sites

Amazing work! Just a heads up, if you want to build a plane after the 2012ish time frame (could also be 15, can't remember right now from the top of my hat) there were two rather visible oxygen bottles installed behind the seat. Oh and I would strongly recommend getting some aftermarket decals - the lighter grey on the Hasegawa markings is very off. Either you manage to find some old Two Bobs (long out of print) sheets somewhere or you wait for the upcoming Caracal Decals sheet (I asked them late April about the potential release date and the answer was "at least 3 months away").

Share this post


Link to post
Share on other sites
Posted (edited)
18 hours ago, Gonzales said:

Excellent stuff, just WOW.

 

Kind regards,

 

Robert Jan

Many thanks for your kind words! It'll never be perfect but that always give me something to work on. There are so many abesolute beautiful builds here to look up to. 

 

7 hours ago, blackwidowmaker said:

Amazing work! Just a heads up, if you want to build a plane after the 2012ish time frame (could also be 15, can't remember right now from the top of my hat) there were two rather visible oxygen bottles installed behind the seat. Oh and I would strongly recommend getting some aftermarket decals - the lighter grey on the Hasegawa markings is very off. Either you manage to find some old Two Bobs (long out of print) sheets somewhere or you wait for the upcoming Caracal Decals sheet (I asked them late April about the potential release date and the answer was "at least 3 months away").

Thanks for your comment. You are right! Now that you mentioned it and looking through more reference photos I think it is a good idea to include o2 bottles behind the pit. I happen to have tidbits in my resin box and once shaved down and modified, makes a good approximation. Ill work on these in the meantime. 

 

I am planning on using the caracal sheet when it is released. At my build rate might be good timing.   Thanks for your advice and suggestions. 

 

UcOf9zc.jpg

 

Konbini

Edited by konbini
Grammar

Share this post


Link to post
Share on other sites
On 6/23/2020 at 2:23 AM, tomfomes said:

Amazing paintjob on that cockpit!!

Many thanks!  My eyes are tired 🤣

 

Update: I added two oxygen bottles behind the ejection seat and added extra detail to the cockpit rear bulkhead. 

 

Konbini

 

7qfLp1W.jpg

 

ZprvbVX.jpg

 

hmy2ebN.jpg

 

haIpxge.jpg

 

N3Exs61.jpg

 

wnovTCB.jpg

Share this post


Link to post
Share on other sites

Outstanding work so far. :worship: Lovely added detail.

Share this post


Link to post
Share on other sites

Great work, I love your cockpit!

 

Dave

Share this post


Link to post
Share on other sites

Oh wow, that cockpit looks AMAZING!  

 

I built this kit somewhat recently, but definitely did not do the detail work you are doing, mine was mostly just an OOB in-flight build.  I do have the remnants of the TwoBobs Langley Raptors sheet, if you would be interested in that, although I am not sure how much useful is left as far as stencils and whatnot.

Share this post


Link to post
Share on other sites

Amazing work. Can't wait to see what you do with the paint scheme.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...