Sean F Posted December 8, 2020 Share Posted December 8, 2020 This is my first build thread, but not my first model kit. I suppose I should upload some photos of finished models in the Display Case. Been modeling since I was a kid, got back into it as an adult then parenting took over (that and the home we lived in had no model space except the garage in the Texas heat which was a no-go!). Got back into modeling again in 2013 after we moved to a new home and been building 1-2 a year since. So this is my build thread of the Kenetic Su-33. Big thanks to BaconRayGun for his build thread here. Lots of good info in his thread and some things to watch out for! First, as he mentions, dry-fit everything, and I mean everything more than once. Their are some questionable engineering decision in this kit and you have to wonder what they were thinking. For example, when you assemble the main gear wheel wells they basically butt-weld the ends! No locating pins, no positive locking mechanism, nothing. Just butt them together and apply glue. You'll see below it's much easier to just insert them into the lower fuselage section rather than try to assemble them as stand alone items. I would compare this kit to the Academy F-4...it can be made in to a nice model, has some good details, but you have to ask what the hell were they thinking sometimes. The ejection seat is another area..just kind of wonky how it all goes together. Anyway, on with the kit. A few starting photos and some progress. This will be a slow thread as I have a tendency to work stop/start a lot and will make a bunch of progress, then nothing for a week or two. The BOX!!!! Extra parts... Disaster right away. One of the resin engine parts was chipped...I was thinking I'm going to have to fix this with some sheet plastic or something then I looked under the foam in the box and the chipped piece was in there! A little superglue and fixed I decided to start with the engines and nozzles and build both the kit and aftermarket to compare them. The kit nozzles have some good details, but are not 100% correct on the insides. Also, the burner flame holders all all photo etch and I have no idea how someone could put these together...just a bunch of tiny brass fingers are supposed to glue together..yeah, right. I just realized I have no photos of the nozzles I've already painted up and I started on the cockpit (I'll post the nozzles later). Here again is an odd way to assemble the cockpit. The floor/front just butts up against the back section/wall area. Their is a small lip it fits into, but it's just not a very positive set up. Then it attaches to the lower section of the fuselage parts...huh??? Never seen this before. Usually it goes into the sidewall or UP into the cockpit combing area so you know you have it fit correctly. I decided to glue it up with white glue first and check the fit and the back part really did not fit all that well. So I decided to superglue the back wall to the upper section, glue in the sidewalls and then primer (Mr Surfacer 1500 black + Mr Leveling Thinner) and paint with MRP (mix of colors to match the Eduard pre-colored cockpit parts. You can see the main gear wells installed here and primer'd white for the final red finish. Quote Link to post Share on other sites
Sean F Posted December 9, 2020 Author Share Posted December 9, 2020 Here are the engine parts. I primed them first with MRP Grey primer, then Alclad gloss black, the a combination of Alclad Jet Exhaust, burn iron, Aluminum and Tamiya clear blue RESIN first; Kit Parts; And here is the main wheel wells I mentioned earlier. Each sidewall is shown in the instructions to just butt-weld together..much easier to just install and glue in place. White MRP Primer, Tamiya Red and Alclad Aqua-Gloss as of now. that's as far as I've gotten so far. Quote Link to post Share on other sites
Sean F Posted December 19, 2020 Author Share Posted December 19, 2020 (edited) Some more progress... The windscreen is a little large and causes the canopy to ride the back hump. I usually install the windscreen and then glue down the canopy with white glue and paint the kits so everything is even and matches on the plane. I could sand down the windscreen so it does not overhang into the canopy but that might remove too much detail. I'll figure something out.... When you attach the front intake of the engines, they do not align and match up with the the lower fuselage. A quick sanding of the flat surfaces that attach at the lower fuselage give a much better fit and no need to sand down the round misfit in the above photo and have to rescibe all that detail. Just be sure and only sand the back area. I sanded down the entire length and caused a slight misfit. But still better than it was. I glued attached the front and rear fuselage portions together and left the wing and canard area free of glue for the time being. It was too difficult to try and hold it all together and glue/rubberband/clamp....also, I hadn't decided if I was going to fold the wings or not and you have to glue in some inserts between the wing halves if you plan to do the wings folded (I later decided to fold the main wings). while that was drying, I moved onto some other area's. The the instructions show the elevator parts go together like this.... Obviously wrong...swap the parts from what the instructions show and the look like this. I did not want to display the air brake open, but when closed it does not exactly fit correctly into the space in the fuselage... So I added some layers of sheet styrene...and a few layers of bare metal foil to get just the right thinkness to lift up the air brake so it fit more flush with the top much better I didn't get a good photo, but the back rudder portion does not fit well (again, just no positive connection points) onto the tail portion. The round front of the rudder butts up against the flat cut out in the tail fin...not good So I sanded things a bit, then put a small piece of styrene on the upper portion of the rudder to get a better joint to glue I did sand down the styrene piece to be round at the front, but it give a much better fit and look of the rear tail/rudder area I've got the wings assembled and will get those pics uploaded....there are a few areas there you'll want to sand away to get the wing halves to fit better but nothing major. Overall its going OK...not the best kit in the world, but it will build up into a nice model once painted (the real reason I bought it in the first place!! 🙂 ) Edited December 19, 2020 by Sean F Quote Link to post Share on other sites
Sean F Posted December 28, 2020 Author Share Posted December 28, 2020 (edited) A little more progress. Got the HUD built up and installed. Came out OK but it will be mostly hidden under the windscreen anyway. I managed to get the windscreen on the front and canopy to fit better with a little sanding of the frame between them and a little off the back of the canopy. Then the IR seeker did not really fit to well so I sanded that a bit to get a better fit up front as well Did you know you can use Perfect Putty on clear plastic and not damage the clear parts? Just let it dry for a minute then use a q-tip in water to wipe of the excess. I actually just figured this out. I knew it was water based so I figured "why not"...sometimes things work out! I put on the windscreen and then mounted all the loose parts for primer. I put black Mr Surfacer 1500 50/50 with Mr Leveling Thinner on the bottom and then just shot Tamiya Grey Primer out of the can on the top. I typically use the black Mr Surfacer for most primers applications, but I've did a model in the past utilizing the black but the topcoat was blue and it just killed the blue (made it way to dark as you'd expect). I did not want to kill the top colors on this one so I primered in grey on top. I was not to concerned about over spray, just wanted a good primer coat. I'll go back later and sand it smooth. Please fell free to comment, good, bad or indifferent. I'm not building a show winner here (would required just way to much effort for this kit) and you will not hurt my feelings! 🙂 Edited December 28, 2020 by Sean F Quote Link to post Share on other sites
Brenhen Posted December 31, 2020 Share Posted December 31, 2020 Great start! It looks like some work, but you're making nice fixes and I'm sure it will look great in the end. Thanks for sharing and keep the pictures coming! Quote Link to post Share on other sites
Dadeo911 Posted January 2, 2021 Share Posted January 2, 2021 Looks like you have your work cut out for you. I have this kit in my stash so I will be following along. Thanks for pointing out the errors and fixes you have found so far. Happy New Years! Chris Quote Link to post Share on other sites
Sean F Posted January 5, 2021 Author Share Posted January 5, 2021 (edited) Make sure and read the link I put above as well. Here is the wing area I mentioned earlier. You'll need to grind/sand down those highlighted tabs where the flaps slide in to get the rear of the wing to fit together without a huge gap at the back. Here is everything primed and the grey coat put on the underside and top areas. I laid it all out to get everything lined up for the blue colors. Here are the engines just slid into place. Resin on the right, kit on the left Resin Version; Kit Engines; Honestly, if you can get the photo etched flame holders together on the kit version, they do build up and look pretty good with some shading/weathering. I've actually note done any shading yet but will get to that. I actually did a freehand for the color coats. I know, not really correct but I did not want all the extra work of masking. This is a few days after paint and I went over everything with some wet 1000 grit to get the bumps down. I've go to go back over all the colors again to clean up some overspray and a few areas the sanding took down to the primer. Also had to clean up some of the panel lines. I may go back and mask of the top colors to get the hard edge they are supposed to have. Not really looking forward to all that extra work though so I may skip it....:) Edited January 5, 2021 by Sean F Quote Link to post Share on other sites
Night Owl Models Posted January 5, 2021 Share Posted January 5, 2021 (edited) Thats great work, yes I know masking is a pain I used to be an avid free hand airbrushed but the more I used masks the easier it became. It is a differt set of skills to use masks correctly just because they give you the pattern it doesn't make for a great airbrushing skills unless you develop those skills. I prefer masking putty and the challange of mimicing the pattern. Even with masking putty you need to know how much paint your laying down, what angle to go in at and how to correct mistakes. I like masks for one particular reason if you look closley at any real aircraft the decimation lines between colors at 1:1 scale are fairly sharp with a slight feather now scale that down to 1:48th or 1:72nd you should almost be at a crisp edge. Over decimation of lines and my pet peeve over weathering on post and pre shadding can ruin an expensive model and dozens of hours. I have a few models on my profile if your interested well almost all I have used masking film or putty even good old silly putty makes a great mask and it very inexpensive. Thanks for the tip on the Perfect Putty I didnt know that iether I an going to give that a try. I recently discovered 3M glazing putty great for those times when you over scribe and need to correct a scratch. Its a bit dark like a deep maroon red but lighten to a pink with a primer and finish coat works out well. Cheers Edited January 5, 2021 by Night Owl Models Spelling Quote Link to post Share on other sites
Sean F Posted January 5, 2021 Author Share Posted January 5, 2021 I know I should mask thr paint, just not looking forward to it! Thanks for the tips on the silly puddy. I read that and blue tack also works. Quote Link to post Share on other sites
BaconRaygun Posted January 5, 2021 Share Posted January 5, 2021 Looking good Sean! I've still not done a damn thing to mine... still sitting in limbo. I really need to get in gear and finish it already! Quote Link to post Share on other sites
Sean F Posted January 23, 2021 Author Share Posted January 23, 2021 Not really much of an update. I went back and used the Blue-Tak stuff to mask and redo the camo scheme. Gosh, that was the most mundane task I've ever done in regards to modeling. I seriously thought about putting it all back in the box and starting something else...cut blue tak, roll out blue tak, stick blue tak on model along camo edge...cut strips of tape to mask behind blue tak....ugg...so glad that's over! I did end up with some ghost like patterns so I pulled the tip off the airbrush, put it at lower pressure and cleaned up a few spots. Overall it looks OK. Need to go back and touch up the dark blue in a few spots. Still need to add the white nose and panels, mask and paint the gun panel and engine area's. Then onto the landing gear and weapons. Thanks...hoping to rap this one up in the next week or two....probably three at the rate this is going! Although the hard part is done now. Quote Link to post Share on other sites
Night Owl Models Posted January 23, 2021 Share Posted January 23, 2021 Great job you did the right thing looks 100% better actually pops more if anything going through the process helps define skills and the next time you'll have it down able to get it done quickly. Look forward to seeing it all weatherd and decals up on its feet. Quote Link to post Share on other sites
Night Owl Models Posted January 23, 2021 Share Posted January 23, 2021 This will make you feel better lol😆 this was the paint job from hell. I was of the same mind half way through...what did I get into here. Quote Link to post Share on other sites
Sean F Posted January 26, 2021 Author Share Posted January 26, 2021 (edited) Small update. Got the white panels and nose painted. Then got the black gloss on the metal areas and started the engine covers. Letting it dry now and will do some clear blue and red tomorrow. Edited January 26, 2021 by Sean F Quote Link to post Share on other sites
Sean F Posted January 26, 2021 Author Share Posted January 26, 2021 Odd thing happened when I was spraying the Alclad II. When I put the first coat of Aluminum down, strings were shooting out from the surface of the model. They did not stick, but it was like the paint was drying in the air. I have a scrap model on my paint bench and no matter the pressure or distance or flow, little strings of paint were coming off the surface. I’ve never encountered this before. I cleaned up the mess, dumped the paint out of the air brush, dumped some lacquer thinner thru the airbrush and tried the other Alcad colors (titanium, jet exhaust, airframe Al) and those all sprayed fine at my normal settings (18 psig). The AK metal colors sprayed fine as well. I’m assuming something happened with the Aluminum color and it’s now bad? Anyone seen this before? I used the same color on the exhaust nozzles and it worked just fine. Quote Link to post Share on other sites
Sean F Posted January 28, 2021 Author Share Posted January 28, 2021 I swear this thing is fighting with me like no kit I've ever built! This is the third chunk of paint thats lifted. You can see another in the dark blue just above thie one in the metal. Ive never had this happen! I, might just "weather" it and move on..... Got the engines done. Gloss coat, weather, landing gear, armaments, seat and cockpit are still left... Typing that actually kind of depressing.... Quote Link to post Share on other sites
Sean F Posted January 28, 2021 Author Share Posted January 28, 2021 I just realized I need to paint those access doors a bright silver color! Quote Link to post Share on other sites
AlienFrogModeller Posted January 30, 2021 Share Posted January 30, 2021 Looking good!! Cheers AFM Quote Link to post Share on other sites
Night Owl Models Posted January 31, 2021 Share Posted January 31, 2021 (edited) Nice job on the engines striking paint job. Edited January 31, 2021 by Night Owl Models Quote Link to post Share on other sites
Sean F Posted February 1, 2021 Author Share Posted February 1, 2021 (edited) Got the gloss coat and decals in place. Not going to do a lot of weathering on this one. Also cleaned up the gear and got the missiles are painted. No decals included for the missiles. I threw the engines into the back but obviously not all the way just to see how they look. Edited February 1, 2021 by Sean F Quote Link to post Share on other sites
ExchefAndy Posted February 1, 2021 Share Posted February 1, 2021 I popped in a few times to check out your work, and I must say... Fantastic! Andy Quote Link to post Share on other sites
Sean F Posted February 2, 2021 Author Share Posted February 2, 2021 (edited) Flat coat is on and I've partially assembled a few things. Although I did not glue the gear in place and I realized last night I need to remove it. Still need to attach a few things and it will be easier without the landing gear sticking out (folded wings, tail, elevators, etc.). In the home strech. Liquid mask worked perfectly around the canopy and windscreen. wings are not actually attached, I just placed them on the fold mechanism to see how they look model table is a mess (like always at the end of a build...stuff just seems to be everywhere! 😉 ) Tail is not attached, just slotted in place. engines are kind of meh...should have just left the silver doors alone. Tried to to it by hand an mucked it up. I suppose I should really go back and mask and do them right. painted the missles with some black rudders (?) - sorry no picks. I think I have a bunch of decals left from the AMK Mig 31 build so I may gloss those and apply some random decals. They just look kind of boring plain white. Edited February 2, 2021 by Sean F Quote Link to post Share on other sites
Sean F Posted February 3, 2021 Author Share Posted February 3, 2021 I tried to remove the front gear and the whole well came loose! I managed to get some superglue inside the well and get it reattached. The missiles will not fit with the flaps down.... Installing the tail! Getting the wings installed folded was a PITA... I'm on a mobile but when i get to a keyboard I'll provide some tips to get them on... Quote Link to post Share on other sites
kurnass77 Posted February 3, 2021 Share Posted February 3, 2021 Look great! Gianni Quote Link to post Share on other sites
Sean F Posted February 3, 2021 Author Share Posted February 3, 2021 Thank you for the compliments all! I did not get my photos uploaded, but I think at the end I'll just summarize all the area's you need to show extra care to get things together correctly. The wing fold parts simply did not fit as they came off the sprue and I had to do some surgery to get them the work. I got the weapons gloss coated at the end of the evening and will let those dry for a few days. I did find my Mig 31 decals so I'll throw some on to add some interest to the plain weapons and get those mounted. Need to weather the tires a bit and get the gear pieces and doors installed. The model is kind of at a delicate stage right now with the wings mounted so it might be slow going. Thanks again for all the kind words. It does look nice in the photos and the paint job really stands out. But their are a lot of little issues on the kit if you look closely. Certainly not a win, place, or show at any contests but I knew at the start that would happen. Really just bought this for the paint job! Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.