Jump to content

1/350 Trumpeter USS Hornet CV-8 Doolittle Raid


Recommended Posts

On 1 April 1942 sixteen modified B-25B bombers were loaded aboard the USS Hornet CV-8. The next day the USS Hornet along with the ships of Task Force 18 sailed towards the Hawaiian Islands. They met up with the USS Enterprise and Task Force 16 then headed across the Pacific Ocean. On the morning of 18 April 1942 approximately 650 nautical miles from the Island of Japan, sixteen B-25B’s Led by Lieutenant Colonel James Doolittle launched off the Hornet’s deck to perform the first air operation to strike the Japanese mainland in retaliation for the attack on Pearl Harbor.

For this next build I am building Trumpeter’s 1/350 USS Hornet as she was during the Doolittle Raid. This is going to be a super-detailed project. It is being built to be displayed at a museum that is creating a display of the raid for the 80th anniversary. This project is estimated to take around 4 – 5 months to complete. There are many aftermarket accessories that will be utilized in this build. So far I have four different sets of photo etch parts just for the ship, a wooden deck, all the B-25B’s as well as all the aircraft that were stored in the hangar bay that were later moved to the flight deck after the bombers departed in case the Task Force was spotted and needed to defend itself. All of the aircraft have multiple photo etch sets for the cockpits and exterior details.  I will also be illuminating it as well. I have many accessories still on order like 3-D printed Moto-Tugs and crew members. At the end of the project I will list all of the accessories I used. I also purchased two reference books. One on the USS Hornet itself and the other covers the Doolittle raid. I also located a shipbuilding drawing of the Yorktown class carriers that covers all the decks from keel to the top of the island. I scaled the hangar deck sheet to 1/350 scale and printed it out so that I can accurately place the interior walls and other details.

Starting with the hangar I began using the White Ensign Hangar bay photo etch set (#3541). The instructions give you sizes and plans to scratch build the hangar bay walls. I installed the hangar deck then painted it deck grey and gave it a basic weathering. I will be doing more weathering/staining once I figure out the layout of the aircraft. Using Evergreen Models 1.0mm styrene sheets I cut out the parts for the interior walls per the hangar bay detail set instructions. I have a few sheets of extra doors and rails from previous ship sets so after building the walls I added photo etch doors, stairs and rails to match the reference photos. The kit walls have numerous ejector pin marks. Instead of filling and sanding all of them I opted to use sheets of 0.5mm sheets to cover them. Also, since I will be illuminating the hangar bay I cut open many of the hangar bay side doors. With the starboard side interior walls assembled per the photo etch set instructions I added all the fine details as they are shown in the photos from the reference book.

After adding details to the forward elevator bay I did some detail work on the bow. One of the obvious things missing from the model details is the bow mooring guides. I used some styrene tubing to make these. I then reshaped the anchor chain holes. On the kit these were just straight thru holes. I used a file to make them angled and flared. I removed the molded chain and will be replacing it with a real anchor chain. There are two supports for the front of the flight deck. I filled the mounting holes for the kit plastic ones and installed the correctly sized photo etch parts from the White Ensign Detail set (#3525).  Working on getting the starboard side interior detailed and installed this coming week.

 

See more photos and details in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5707-1.jpg

 

dscn5710-1.jpg

 

dscn5717-1.jpg

 

dscn5720-1.jpg

 

dscn5721-1.jpg

 

dscn5725-1.jpg

 

dscn5733-1.jpg

 

dscn5735-1.jpg

 

dscn5737-1.jpg

 

dscn5740-1.jpg

Link to post
Share on other sites

This week’s update on the USS Hornet covers more work on the hangar bay walls. I also started my experiments on add illumination to the hangar deck. I do not have all the lighting figured out but I have a general idea on what I need to do and a good start on how to accomplish it. 

Back to the hangar bay walls, the kit walls have many ejector marks so they have all been covered with 0.5mm styrene sheets. I then use extra rails and doors to detail them. On the thin hangar walls that lead to the outside I matched the doors on the inside. I framed the areas around the doors and for the doors that are closed I scored the surface to match the same detail as the outside. I still need to make the rolled up doors for the open ones but I need to wait until I install the flight deck supports. These will also affect where the wiring for the lights will go. I have also added a couple of stokes litters and a hose reel for where the Moto-Tugs will be parked. Another thing I need to do is to remove the guilds on the hangar deck for the walls. This is because with opening doors and with adding details to the inside of the wall they get in the way.

For the lighting each support has lights hanging from their edge. (4 to 6 per support) There are total of 166 lights! I took some 0.5mm fiber optic lines and using a lighter I slightly melted the end to look like a bulb then dipped it in acrylic gel medium. Once dry I cut the excess gel off where the "bulb" part is and primed it all white except where the bulb area was. I used an individual Pico LED to see how the lighting would look. The effect came out perfectly. Now I just need to make 165 more and figure out how to mount them and illuminate them.

As for extras, I received Hornet Air Wing decals from Starfighter Decals. These are for the battle of Midway aircraft so I will need to make the red dots for the center of the insignia for the Doolittle raid version. I also could not find 1/350 decals for the Doolittle B-25B’s so I made my own including the few aircraft that have nose art. The other accessories I received were ten 3-D printed moto-tugs thanks to BaconFist on Shapeways and I have 3-D printed officers and enlisted crew from HOLDEN8702RD on Shapeways.

Next up is the finishing of the hangar walls then I will need to start making all the aircraft, accessories, and figures for the hangar deck. These will need to be installed before the flight deck supports and lighting can be installed.

See more photos and details in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5742.jpg

 

dscn5745.jpg

 

dscn5747.jpg

 

dscn5749.jpg

 

dscn5750.jpg

 

dscn5753.jpg

 

dscn5759.jpg

 

dscn5761.jpg

 

dscn5763.jpg

 

mb-25b-decals1.jpg

 

mb-25b-decals2.jpg

Link to post
Share on other sites

Work continues on the Hornet hangar bay walls.  While reviewing the few photos I have I noticed that the hangar doors roll up. I used some styrene tubing for the open doors and rods for the closed ones. The open door ones were painted the exterior color 5-O Ocean Blue due to how they would roll up. As for the brand of paint I am using, I will be using Scale Colors for the ship. The colors are 5-N Blue, 5-O Ocean Grey and 5-H Haze Grey. Once these were installed I then began to add fine details to the walls. I added doors to match the ones on the outside and then added ducts for the vents on the port side. A few platforms with railings and stairs/ladders were added as well. Other details I noticed in the photos were added as well. There are many pipes and cables which will be added later. I will be using the pipes to hide wiring and fiber optic lines when I add them. The walls were then painted and installed. I am currently working on the aft elevator then I need to build up and detail the fantail. This coming week I have a couple of days where I won’t have time to work on this but am planning on starting the aircraft by the end of the week.

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5775.jpg

 

dscn5781.jpg

 

dscn5782.jpg

 

dscn5793.jpg

 

dscn5794.jpg

 

dscn5796.jpg

Link to post
Share on other sites

This week the work on the USS Hornet was limited. I was “forced” by my lovely Wife to spend a relaxing weekend on the lake fishing. We both had a great time and caught many fish

Anyhow, back to the build. I finished up the aft elevator and the fantail of the ship.  I then moved on to some aircraft. During the trip across the Pacific the Hornet had its normal compliment of aircraft packed on the hangar deck while the B-25B’s remained on the flight deck. I need to build all these aircraft so I can finish the hangar deck. I purchased all of the photo-etch for these aircraft. Both Tom’s Model Works and White Ensign Models provide sets. The Tom’s provides landing gear, antennas, and propellers for each aircraft. White Ensign has some cockpit details (like the rear gunner for the SBD’s) as well as flaps for the aircraft. I decided to start with the F4F Wildcats of “Fighting 8”. Using the F4F that came with the kit I built it up to the point it was ready for decals. One of the things I noticed was they have a hole for the landing gear that comes on the tree. Since I was using the photo-etch landing gear I took a small drill bit the diameter of the main gear wheels and drilled into the fuselage to create the wheel wells that are on the real aircraft. I looked at using the photo-etch cockpit pieces but the canopy is very small and thick. You would not see any detail at all. So I opted to just paint the interior green and flat black for the instrument panel under the canopy. For the propeller I need to make the shaft into the engine. The hole in the propeller and hub are 0.5mm as well as the on the aircraft cowl. I took a 0.5mm fiber optic strand and used a lighter to melt the end slightly to make it the propeller hub cap. The propeller hub then blades were slid on and painted. The landing gear and antenna on the dorsal behind the cockpit were added. It was base coat painted for the intermediate blue and grey scheme. With interior green for the wheel wells and white for the main gear struts and hubs. I then took the other 17 aircraft and created an assembly line. I am building them up until the point of adding the photo-etch. As soon and all 17 are at this point I will add the photo-etch details and then paint them. After they are built up I will use the individual aircraft decals that are part of the Starfighter Decals Hornet set. 

 

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5799.jpg

 

dscn5801.jpg

 

dscn5802.jpg

 

dscn5808.jpg

 

dscn5811.jpg

 

dscn5812.jpg

 

dscn5813.jpg

Link to post
Share on other sites

It has been another week of work on the USS Hornet CV-8 aircraft. I am still working on the F4F Wildcats. For this week I am showing all the little bits of Photo etch and the process of adding them to the aircraft. Once the fuselage is assembled I added the main gear which consists of the main strut, the landing gear doors, two struts, and a tail wheel. The main strut is added first then the doors. Getting the struts in position using very fine tweezers then gluing in place takes a little time. I find the Glue Looper V4 tip works very well for placing two very small spots of glue on the fuselage and main gear. Once dry I then place the tires and outside hubs on. I pre-painted the parts but they will require touch up after bending and gluing them. I then added the tail wheel. There is a slot for the kit tail wheel so the photo etch version fits into and using medium viscosity CA glue it fills the gap on each side since the photo etch part is a lot thinner than the kit tail wheel. After it dries I then do paint touch ups and paint the underside grey. While the landing gear dries, I assemble the propellers. I included a photo of the assembly showing the fiber optic with the hub and propeller separated to show the process. There is a total of 18 F4F’s that are being built. I am hoping to finish them next week so I can start on the others.

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5818.jpg

 

dscn5823.jpg

 

dscn5825.jpg

 

dscn5824.jpg

 

dscn5831.jpg

Link to post
Share on other sites

Progress this week is going slowly on the USS Hornet build. All things being equal 1/350 modern jets are much easier to build than World War II fighters. With the landing gear finished I needed to install the antennas. Using the Glue Looper V4 and a Pic-N-Stic I was able to place a small drop of CA glue and CAREFULLY place the antenna.

( Check out the Tips and Tricks section for the items I used at https://davidsscalemodels.com/tips-and-tricks/photo-etch-tools/ )

It may look easy but it took one evening just to install them on 18 aircraft. With all the photo etch added I painted all the aircraft and their wings. With the wings being in the folded position I needed to put the decals on before the wings. I had purchased the Starfighter Decals Hornet Air Wing decal set. I am not sure if it was the decal film was too thin or somehow they got degraded but the squadron numbers and the aircraft numbers on the cowl were very difficult to slide and place. They kept falling apart and cracking. After messing up many of them I decided to just make my own numbers. I printed out a set for all the squadrons and replaced the ones that messed up with my own. With the decals all placed I added the canopy, wings and propeller. So the first F4F is done, only 17 more to go! Once these are finished I will be starting on the Devistator torpedo aircraft.

 

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5834.jpg

 

dscn5838.jpg

 

dscn5842.jpg

 

dscn5844.jpg

 

dscn5845.jpg

 

dscn5850.jpg

Link to post
Share on other sites

The F4F Wildcats of “Fighting 8” for the USS Hornet are completed and aboard! I set up an assembly line. First I placed all the decals on the wings and lined them up. The decals were then applied on the fuselage. While they were drying I grabbed one of the 3-D printed Moto-Tugs from BaconFist on Shapeways and painted one of them. The detail for such a small tractor is awesome. The engine was painted engine gray. The body was painted intermediate blue with a black dash and seat. I also painted the front grill openings and tires. Once the Wildcats were completed I placed them in the aft hangar bay. I will set them in place later when I add the figures. I am finally starting the Devastators for “Torpedo 8” today.

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5853.jpg

 

dscn5857.jpg

 

dscn5862.jpg

 

dscn5866.jpg

 

dscn5869.jpg

 

dscn5877.jpg

 

dscn5881.jpg

 

dscn5874.jpg

Link to post
Share on other sites

This week I started working on the Devastators for Torpedo 8 for the USS Hornet. I am using White Ensign’s cockpit detail set #3548 and Tom’s Modelworks aircraft detail set #3538. The cockpit fits very well. I plan on having some of the aircraft with the canopy open and some with the canopy closed. Just like the Wildcats I set up an assembly line. Mounting the cockpit and seats first then assembling the fuselage. The detail set includes the rear gun, antenna, and the gun sight. One thing to note, The instructions for the aircraft assembly show the wings folded pointing straight up when in reality they fold over. Next I will be starting to paint the fuselage section and wings in preparation for the decals.

 

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5883.jpg

 

dscn5886.jpg

 

dscn5887.jpg

 

dscn5893.jpg

 

dscn5895.jpg

 

dscn5899.jpg

Link to post
Share on other sites

The Devastators for Torpedo 8 are almost finished. I added the landing gear and wheels. The landing gear required some tedious work to get them to line up together. There are 3 attachment points so getting the left side and right side to line up as well as stand straight from the front took a lot of work. The landing gear struts were then painted aluminum, tire black for the tire and then the medium grey for the hubs and underside of the aircraft. The top was painted intermediate blue. The wings required a lot of work as well as they had a lot of flash. Especially on the trailing edge which is also very thin. Once finished they were painted. I then looked at the decals. The ones that came with the Trumpeter kit had the incorrect blue for the insignias so I will be using the Starfighter decals. This morning I was going to start applying the decals however, I was looking at some reference photos and noticed the antenna is incorrect. The one photo from the side looked like the antenna was offset similar to the vindicator and dauntless. It turns out the antenna on the devastator is actually just behind the cowl and centered. So I need to correct that today. Once I correct them I can start the decals. Hoping to finish the Devastator’s during this nice long Labor Day weekend then start on the Dauntless dive bombers of Bombing 8.

 

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5901.jpg

 

dscn5903.jpg

 

dscn5907.jpg

 

dscn5910.jpg

 

dscn5911.jpg

 

dscn5912.jpg

 

dscn5918.jpg

Link to post
Share on other sites

The TBD’s of Torpedo 8 are finished. After I spent an evening correcting the misplaced antenna the canopies were added and then I applied all the decals to the fuselage and then the wings were painted and decaled. The wings were carefully placed in the folded position. With the aircraft drying from adding wings and decals I painted all the propellers and trimmed them to mount onto the aircraft. Once dry all the propellers were added to complete the aircraft. They were all staged on the hangar deck.

I then started on the SBD Dauntless dive bombers of Bombing 8. The fuselage required some trimming for the cockpit section to fit. I then grabbed some reference photos. The reference photos show that some aircraft have the dive brakes open and some closed. I will do the same with some open and some closed. I also realized that the SBD Dauntless is missing one thing that most Navy aircraft have, folding wings! So once I get these all built I will need to figure out how to get all these aircraft on the hangar deck. Anyhow, getting back to the build, the cockpit photo etch has a tub with a seat and an instrument panel with pedals. There is also the rear gunner seat, gun mount, and gun which needs to be placed after the fuselage is together. I also have the photo etch set that includes the bomb swing and the dive brakes. I will be using the photo etch dive brakes on a few of them. I am working on setting up the assembly line for them now.

 

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

 

dscn5919.jpg

 

 

dscn5921.jpg

 

 

dscn5923.jpg

 

 

dscn5926.jpg

 

 

dscn5929.jpg

 

 

dscn5930.jpg

 

 

dscn5940.jpg

 

 

dscn5947.jpg

 

 

dscn5950.jpg

 

 

dscn5951.jpg

 

 

dscn5957.jpg

 

 

 

Edited by Wolfman_63
Link to post
Share on other sites

The SBD’s of Bombing 8 are getting closer to being completed. I made one of them with canopy open and dive brakes open. There will be two more with just the rear gunner canopy open and the rest will be all closed. I had to fill in the hole for the tail wheel so I could mount the photo etch version. Another thing I am doing is since the SBD’s do not have folding wings some of the aircraft on the ship had their wings, bomb swing, and propeller removed then the fuselage was hung in the rafters of the hangar bays. So there will be a wing rack as well as a rack for holding the propellers as well as spare propellers for the aircraft. I also found some reference photos of how the aircraft were arranged in the hangar bay. The very few photos I found show the F4F Wildcats forward, TBD’s mid-ship, and the SBD’s aft. So once the SBD’s are finished I will map out where the aircraft will be placed on the hangar deck.

The photo etch set also has bomb carts and torpedo carts which will be added to the hangar near the weapons elevator. I bought some brass early MK 13 torpedoes to place on the torpedo carts. I am hoping to start working on the hangar deck details and crew next week. Still need to figure out the routing for the fiber optics to illuminate the hangar deck as well.

See more photos and details from the start in my build log at https://davidsscalemodels.com/build-log/1-350-uss-hornet-cv-8-doolittle-raid/

 

dscn5958.jpg

 

dscn5959.jpg

 

dscn5961.jpg

 

dscn5968.jpg

 

dscn5971.jpg

 

dscn5972.jpg

 

dscn5976.jpg

 

dscn5977.jpg

Edited by Wolfman_63
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...