Modelkeenfan

You are a champion!!!! Ok let me know Many many thanks

Hi all Could someone tell me the sprue numbers and individual part numbers of the AIM 2000 Iris T missiles in the 1/32 Trumpeter eurofighter Typhoon kit? Many thanks

I'm wanting two 1/32 AIM 2000 Iris T air to air missiles. These missiles are included in the 1/32 Trumpeter EF 2000A typhoon kit. So if anyone has two they could sell, please PM me. Cheers

I'm after a 1/32 academy or AFV F16D clear canopy. If anyone has one to sell, PM me. Many thanks

I'm after a 1/32 academy F18D canopy. If anyone has one to sell, PM me. Many thanks

Hi all. Im wanting a pair of F16 block 30/32 main wheel bay doors. If anyone has pair to sell or swap for a pair of block 50/52 wheel bay doors, PM me. As most would be aware, the inside of the block 30/32 wheel bay doors are quite different to those of the block 50/52. So I hope someone can help me out. Either academy or Tamiya doors are ok Cheers

Hi all. Im wanting a pair of block 30 main wheel bay doors. If anyone has pair to sell or swap, PM me.

The problem is that the 1/32 trumpeter EA18G does not include the 7 antennas and humps and bumps that the growler has. That is why I need pics so I can scratch build these antennas and humps and bumps to make s correct growler. The trumpeter kit is essential just a F18F with the underwing and wing top jamming pods. Why trumpeter didn't include these parts is astonishing. When a company makes a kit, they should at least get it correct. On this occasion, trumpeter has done poor job but at least they put the ACS rear cockpit in the kit.

Thanks for that. In the pics of the centennial, you can see the two little humps just under the stabilators but none of any others. I think there is about seven different antennas and humps. There is is a very distinctive hump on the spine of the fuselage just in front of the twin tail fins and I dont know where the others are. So that's why I'm trying to find pictures of each and all the antennas and humps and bumps. Its hard to find pics.

Hi all I'm and wanting pictures of each individual antennas and humps and bumps housing avionics on the EA18G Growler which are not on the F18F or F18E super hornets. Can anyone provide me with pictures of these preferable close up pictures but any pictures where they are visible and clear to see would also be fine. If anyone can help, it would be most appreciated. Cheers

Guys I see SAC make a set of 1/32 landing gear for a hasegawa F-16A. This would obviously be lightweight landing gear but will it fit the academy and Tamiy kits? Anyone know?

Just had another thought. What about the 1/32 SAC metal F16 landing Gear for thé Hasegawa kits? Hasegawa only produced the F16A so the SAC metal landing gear they make for the hasegawa kit should be the lightweight landing gear. Would I be correct in making that assumption?

Ok Dave. I'll continued my search. Many thanks po

Hi all Im. Looking for a set of academy 1/32 lightweight landing gear and a set of 1/32 Tamiya lightweight landing gear. I'm happy to buy them or swap them Shoot us an email if you can help out Cheers

Thanks guys for the info. There is just one last question, but I can't remember it, so I'll get back to you all

Also guys I bought the 1/32 Aires F16 sufa wheel bays to use on my F16D as I couldn't find any 1/32 Aires F16C wheel bays for an academy F-16. I now see Aires do make a set of 1/32 wheel bays for academy F16Cs. Can anyone tell me if there is any real external differences in the sufa wheel bay to a F16C wheel bay. Will I get away with using the sufa wheel bays for my F16D?

Yes Niels thanks for all the links. One last thing. I read that the F16N had reinforced wings with stiffeners. Are these visible on the aircraft or were reinforced from the inside?

Thanks niels

I solved one problem, I found a 1/32 academy F16 two seater canopy for my my F16D project. God they are like trying to find an extinct dodo bird. So happy I got lucky there

Ok. Any other ideas for finding lightweight landing gear? Ive tried about everywhere to get some without luck

Thanks Niels. Just one thing I haven't got a response too is can anyone tell me if the 1/32 SAC metal F16 landing gear #32020 which is designed for use on Academy F-16 kits is the lightweight landing gear? Secondly, does anyone know if it will fit the 1/32 Tamiya F16CJ kit using Aires wheel bays? Do you know Niels? Or does anyone else know? I've looked everywhere and it's the only set of landing gear I can find except for the 1/32 SAC F-16 landing gear for the Hasegawa kit (which is very different in dimensions to the Academy and Tamiya kits) So I'm assuming as Academy only make one F16 kit with heavy landing gear being the F-16I SUFA, then I'm also assuming this SAC landing gear for Academy F16s is the lightweight landing gear. Can anyone let me know? Cheers

Hi all I know I'm posting a bit on F16s. However it's the fast jet I know least about due to the many versions and small details which differ on version to version. I'm planning to convert a 1/32 Tamiya F16CJ to a F16N. So my plan is as follows Purchase the 1/32 GT resin small mouth intake for it Purchase the 1/32 avionix F16 block 30/32 cockpit wet Ommit the two small parts on the tail which create a small air intake Eliminate the gun and gun port on the F16 Put the landing lights on the main gear struts Buy the 1/32 SAC metal landing gear and put the small tyres from my Thunderbirds kit on it (does anyone know if the 1/32 SAC metal landing gear made for the Academy kit will fit the Tamiya kit? And is this SAC set the lightweight landing gear?) On the main landing gear wheel bay doors, I will sand off the humps on both doors so they are the flat doors used with the light weight landing gear. Put the relevent antennas on in the correct places and place an ACMI pod on the right wing tip Now can anyone tell me anything I've missed or anything I need to do to make the conversion? As I understand it, the airframe of the F16C block 30 is the same as the F16N airframe IE - tail and tail base is the same on both versions Any help with answering my questions on the 1/32 SAC landing gear would be appreciated or anything I've missed in making the conversion Thanks all for reading and if anyone can help in anyway. Cheers

Also some pics of different aggressors in it

Sorry about that. The sold reply didn't appear when I opened the thread.

Hi there Have you still got the NSI intake for sale? I live in France but can have you post it to a friend in Oregon who will forward it on to me. PM me if you still have it Cheers